Jump to content
SAU Community

Recommended Posts

Hey ppls,

I've recently pulled the cams out to find there's a little scoring and some polishing on 2 of the cam caps. All pretty much have ever so slight scoring but only 2 have what is noticeable so to speak and one looks a tad concerning.

Is this normal? I've pulled the caps off an rb20det I have here and it has the same but not as bad as the one that is a tad concerning.

The tunnel is perfect absolutely no scoring what so ever. its only on the caps.

Is it worth attempting to try and polish/linish out the slight marks or just slap it back together with the new cams?

One last thing to mention is on the surface of some of the cam caps i can see what looks like a black mole... doesn't look burnt just ever so slightly black; much like what a light black skin spot looks like with its faded edges.

Link to comment
https://www.sau.com.au/forums/topic/224487-cam-bearing-caps-and-scoring/
Share on other sites

Nizmonut... You can't buy replacement journals for these I am led to believe.

GTR1993.

There's no oil supply issue that I know of.

I pulled the caps off quite some time ago and there were still a few light lines inside the caps all though they almost looked like machining lines; to touch they can't be felt.

The only difference to now is 1 of the caps mainly has got a tad worse which is concerning and it just happens to be cap 6. Even though the mark is visible it can't be felt.

I am however running a single 1.5mm oil restrictor and blocked rear as recommended by SK.

There's no hydraulic lifter tick and plenty of oil floating around. Oil pressure is spot on and doesn't bleed off on idle.

I've found a few other pics of caps that also appear to have the same strange circular lines inside the caps.

Its also interesting that the lines are ONLY on the cap not the actual tunnel/lower half; the tunnel/lower half looks spot on. BUT I would expect it to as there is next to no load placed upon on it.

Possibly time to take them down for a check up at the local workshop to see what can be done.

Hi Cubes,

what you are looking at it due to 2 things.

1. the caps have been tightened by the looks of it down to 50nm. and due to the fact they are alloy the upper bridges compress to form an elipse causing scoring on the top of the profile.

2. the head may have been suffering from oil starvation due to lack of pressure.

there is really only the option of getting the arcs machined/honed and decking the contact surface so the still form a good base circle, or getting other caps from a decent head and torquing them down to 26nm IIRC?

there is also the possibility of foreign particles in the oil. were these pulled from a running engine?

cheers :P

Only problem is that even if you could get new ones each one of those journal caps is unique in mount offset, easy way to see is to swap some of those caps around and youll see presto hole is now off set by up to 1mm on some motors, Nissan obviously bolts them all up and line bores so that even if there is slight variance in the cap mount the hole is still perfect. So if you need to replace any you will need to line bore it. Easy way to do it is to have .5mm taken off the caps, bolt them all up and have it line bored, its only the caps that score not the head due to valve spring load.

The guys here in South Africa always use oil filters that dont have anti drain back valves which causes gauling and damage to the cam caps especialy in SR20's, takes up to 10 seconds from start up for the oil to start coming out the spray bars with no drain back valve in the filter.

It cost about the same here to have both sides line bored as it does to bore and hone the same size motors cylinders, cant imagine it being that much more in Ausi

Cheers Shanef and thanks all.

Gulp/Swallow.... Here's the pic of the exhaust cap 7 to 2 from left to right respectively.

Closer inspection. The black marks on cap 7 is actually corrosion. :S

I do remember it being there ~80,000km's ago when the motor first went in; it doesn't appear to look any worse from 'memory' but it was a long time ago.

The camera has shown up fine scratches that i can't actually see by eye unless i get really really close and shine it on certain angles in the light.

You can see the polishing on the lower (pic) side of the cap.

If it has to be line bored it has to be done. :laugh:

post-382-1213793603_thumb.jpg

what you are looking at it due to 2 things.

1. the caps have been tightened by the looks of it down to 50nm. and due to the fact they are alloy the upper bridges compress to form an elipse causing scoring on the top of the profile.

What is the correct tightening torque???

cubes, on second look they dont look to bad at all.

if you run your nail over the scratched can you feel them? or does it feel pretty smooth? they looked worse in the first picture

That first pic was some other motor that I found via google.

Yeah they aren't too bad but yeah the corrosion + I really am not sure if they should have absolutely no scoring or a little is fine.

Running my nail over it its not perfectly smooth but the nail definitely doesn't catch on it so to speak.

Rezlo.. Thanks for the pics buddy. The RB's have the anti drainback located in the block. I'll head down before work starts and have them checked out juuuuustt incase.

Wouldn't want to scatter alloy fillings through out the motor. :S

Some more pics that I took in daylight.

The inlet is definitely in better nick than the exhaust but one still has corrosion/cancer.

Couldn't get down to have them checked out today. Will have to be next monday now. :)

post-382-1213840301_thumb.jpg

post-382-1213840312_thumb.jpg

Yeah I know the RB does, just an example of the repair.

Honestly yours dont look that bad, that spot or corosion is tiny, I would say dont bother unless your running some hard core cams and springs which would load them a lot more than stock.

Edited by Rezlo
does anyone have a spare set of caps? i need a set (or 2- to try and match up as close as i can, then to line bore out.)

pm me if anyones got any

thanks

Why dont you just have them taken down .5mm or 1mm and reuse them? even if you find the near perfect cap and its got a TINY TINY offset and you line bore it would mean that only 50% of the new cap will get machined, and it will be on they higher side of the stock specs, if you machine yours down and reuse you can get pretty much the exact factory clearance + cost savings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...