Jump to content
SAU Community

Recommended Posts

Depend on how's your shifting now, if it feel notchy and difficult in engaging, then the MTL(70w80) would work better then thicker 75w90 oil as the thinner oil will squeeze out faster from the syncro thus promoting quick positive shift. RL lightweight shockproof & 75w90 gear oil do already contain LSD additives, the amount of additional LSD additives to add will depends on the level of LSD noise(how tight or losses is the LSD).

There's no real answer to your question, it's more of an educated guess with trial and error thing. I would suggest you add a quart of 75w90 to your front with remaining MTL and see what happens.

Ok sure, the gearbox is not notchy or difficult to engage from memory.

The front and rear LSD's appear to be very tight, the front clunks on gear change, does that mean I use a little more additive in the front?

And for very tight LSD's is Redline Lightweight shockproof OR 75w90 make more sense? (both diff's seem to be tight)

I have the quarts of MTL for the gearbox for now, I will see how that goes after the change I guess :D

Edit: Oil change complete now. The rear diff is the one whining and clunking, maybe the front was making some noise before but its silent after adding Redline Lightweight shockproof. It had a clear oil in it when it was drained (clear/white sort of colour).

Haven't done the gearbox but engine in running smoothly on Castrol 5w40, hasn't gotten over 85 degrees yet but hasn't been driven too hard. Still very noisy lifters but thats probably normal.

Also did transfer case with some Penrite fully synthetic dextron 3, front diff seems to engage a bit more often now (not just on when turning and accelerating).

Thanks for the reply.

drifter_r33 read the damn thread, its got plenty of information of what to use.

5w50 doesn't sound like the best oil for a GTR, Mobil1 0w40 is said to be good.

So is German Castrol, 5w40 and 0w30, RoyalPurple, Redline (expensive but very good) and Motul 300V(?) (also expensive).

4.75 litres is the amount for an oil change including a filter, I don't know how much your oil cooler would need.

Hi guys, i need your help.

i have got an r33 gtst, and i have been useing OWS 5W50 for the last 6 years, but now its getting harder to get this oil, so below are my 2 options.

1. 8100 ESTER E-TECH 0W-40

2. Mobil 1 0w40

Now here is the confusing part, reading this thread people seem to think that Mobile 1 is a better oil than 8100, but this is the new one with ester, where as Mobil 1 is not an ester based oil.

To make things more harder Mobil 1 meets Mercedes MB 229.5 standards where as 8100 only meets Mercedes MB 229.3, don't know how much difference this makes but i thought i might as well throw it in here.

Car's a 96 model with around 220rwkw running an hks 2530 on 17psi and is tunned to run very rich, its got about 90,000ks on it.

Edited by MUFASA
hi Guys,

I have a Penrite SIN10 10W-70 that was given to me. now will this be fine for a R34GT (RB25DE) ?

its free so im thinking of using it but not really sure if its fine to use.

Thanks

It's too thick, buy another bottle of Penrite 5w30 and mix 60/40 to thin it down.

Ok, another question about my rear diff. The rear diff locks on most corners and the whine/clunk is getting looked at in the next fortnight (finally!).

However, it would appear that the rear diff is likely aftermarket and I don't think stock diff's lock on corners as much as this diff does.

Does the recommendation for the Redline 75w90 oil in the rear diff still correct? Or should I be using something else?

  • 2 weeks later...

Does anyone know what group base oil Royal Purple use? i have been reading their site but its seems more like marketing then technology? the API rating is V bad.

I have always been a penrite man but after reading this thread and many others it seems the sin 5 is too thick for the RB26, I have purchased RP 10-40 but am starting to think i should have just stuck with a proven performer i.e M1

Cheers

Damien.

Does anyone know what group base oil Royal Purple use? i have been reading their site but its seems more like marketing then technology? the API rating is V bad.

I have always been a penrite man but after reading this thread and many others it seems the sin 5 is too thick for the RB26, I have purchased RP 10-40 but am starting to think i should have just stuck with a proven performer i.e M1

Cheers

Damien.

they done a bearing test on this oil less marks than the rest off them its was in the magazine i had a while back if i findit ill post the shit they talked about ive been using this oil for over 6months not a problem with it its reall smooth and you do notice the difference dont be a girl try it i have and havent gone back to penrite and that.

i knoe its not the answer you looking for but i just hadto :banana:

Edited by R334door(s2)
  • 2 weeks later...

guys i changed my engine oil to motul power 4100 15w/50 and its been running a hell lot quiet as compared to the last fuel change with elf but the problem is now i noticed that the fuel pressure is very very low. The normal value should be at a value between 3 and 4 right?Now at cold weather it drops until 1 and i'm really worried at this. Sometimes when i warm up the car and it idles for 3 minutes then die. Can someone suggest me if its the engine oil that is causing the problem?(i have no problem prior changing it to motul)

guys i changed my engine oil to motul power 4100 15w/50 and its been running a hell lot quiet as compared to the last fuel change with elf but the problem is now i noticed that the fuel pressure is very very low. The normal value should be at a value between 3 and 4 right?Now at cold weather it drops until 1 and i'm really worried at this. Sometimes when i warm up the car and it idles for 3 minutes then die. Can someone suggest me if its the engine oil that is causing the problem?(i have no problem prior changing it to motul)

righto... :) is anyone as confused as me about what this guy is talking about with fuel pressure?! You obviously meant oil pressure.

your oil you are using is probably a bit thick on cold nissan quote a 7.5W/30 i think from memory, so you are well above this. Try somehting like a 5W/40 or possibly a 10W/50 from what ive tried they are both fine and do the job well. Make sure they are fully synthetic aswell.

Whether its the problem to do with the oil...i doubt it but changing your oil wouldnt hurt you in this case. Dont go by teh stock oil pressure guage either, they are prone to irregular/incorrect readings depending on the age of the car/sensor. Chances are you've got a vaccum leak somewhere, or something along those lines and this is causing your idling cold start issue. Try using the Search feature and look for idling issues and im sure you will find something that will help you out.

Have fun

David

they done a bearing test on this oil less marks than the rest off them its was in the magazine i had a while back if i findit ill post the shit they talked about ive been using this oil for over 6months not a problem with it its reall smooth and you do notice the difference dont be a girl try it i have and havent gone back to penrite and that.

i knoe its not the answer you looking for but i just hadto :worship:

and so many times in this thread have we explained why that test was total bs. so forget about it.

However RP tends to be Group V and has had good results although I have been using redline for the past 2-3 years.

UNless your car sees the track dont go over a 40wt.

Hey Guys,

Im currently using mobil 1 5w-50w fully synthetic. The previous owner used Shell oils, and i noticed there were some lifter noises coming from the engine, however after putting mobile 1 into the engine it quitened down a bit. I was told that it will take a few oil changes with mobil 1 fully syn for it to show a huge improvement...

Ive been reading through these pages on oils and it seems that as long as you use fully syn and change the oils frequently the actual "Brand" name per say, is not really a huge factor.

Same here ! Pennzoil Full Synthetic 5W-50 for the last year or two and no problems. I Use the OEM filters.

I think as long as you don't forget the OEM spec, and work around them, you can't go wrong far wrong.

NISSAN recommend their oil which is 7.5W-30 from memory with 3,000km oil change intervals for a GT-R in Australian conditions. So, anything that has a cold weight of 7.5W or better ( eg 5W or 0W ) and hot weight of 30W or better ( 40W or 50W ) should do the trick.

But like someone has already said, having ENOUGH oil is THE most important thing.

same used the pennzoil fully synth 5-50w for a change and had a good run with it....couldnt find it next time around so swithched to mobil 1..and much the same feel.only the mobil has been slightly better in the long run with same response, so will use it or move up to motul oil .........

The 300V of course. :sorcerer:

wait a minite the 300v is a 15-50w oil..pretty thick for performance only?.....would you reccomend that for standard street use?

i have used used mobil 1 5-50w and found it unimpressive .

nexy will be 0-40 w mobil1 synth for sure...will probably stick with it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...