Jump to content
SAU Community

holes in front bar...


Recommended Posts

ive noticed that on gt-r's the vspec's dont have these 'speed holes'.. but normal gt-r's do... i would have thought it would be the other way around if anything:)

R32 GT-R V-spec

6000010011258A.JPG

R32 GT-R

2000003255850A.JPG

same deal with 33's... havent looked at 34's though, probably the same.

Link to comment
https://www.sau.com.au/forums/topic/2271-holes-in-front-bar/#findComment-41696
Share on other sites

hhmmm "speeeeed holes hey"???

Speed Holes.. how funny is that..

I thought the 2 holes were called N1 bumper inserts.

Isn't there an N1 version in all the GTR's

or did they just do that in the R34 and all the other GTR owners saw them and thought "sweet" I'll take 2 of those there speeeed holes..

I'm going home to take to my bonnet with a axe... I'm a get me some of them there speeed holes..

Link to comment
https://www.sau.com.au/forums/topic/2271-holes-in-front-bar/#findComment-41792
Share on other sites

GTST there was an n1 in all models of the gtr, boo5t the cars you see that arent n1 with this they have been fitted later or the front bar has been replaced thats probs why you see more run of the mill R's with them these cars are more likely to have a new front bar.

Link to comment
https://www.sau.com.au/forums/topic/2271-holes-in-front-bar/#findComment-41821
Share on other sites

officially they are called N1 front bar slots. i wouldn't mind getting those as a later addition to my car... they arent too much either. UAS quotes $100 for the fibreglass ones for an R32, which is cheap.... oh and of course fitting, dunno how much for that though... hehehe speed holes... from the simpsons! :)

Link to comment
https://www.sau.com.au/forums/topic/2271-holes-in-front-bar/#findComment-42066
Share on other sites

from my understanding, R33 Series 3 GTR's have these in the bars as standard, of course N1 GTR's have them as well

Series 1 and Series 2 R33 GTR's don't have them (unless they are aftermarket / add on)

not sure on R32's or R34's.. but yeah they flow a little more air into the top of the intercooler,

i guess they may even increase flow into oil coolers as well depending on where they are fitted, but it is probably too low down for that..

Link to comment
https://www.sau.com.au/forums/topic/2271-holes-in-front-bar/#findComment-44039
Share on other sites

Yeah on the r32 gtr they are from the N1 kit. Ive got em for my GTst which has original GTR bar, theyr bout 350 each side from nissan, but fortuantely I got em original for 250 together. They go with the N1 lip on the bonnet, N1 rear pod on side skirt, and the lip on the boot lid under the spoiler.

Mainly purley a look thing

Regards

Will

Link to comment
https://www.sau.com.au/forums/topic/2271-holes-in-front-bar/#findComment-44160
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...