Jump to content
SAU Community

Recommended Posts

it's getting close now, just had my leave approved, and Damo and I will spent the long weekend doing recce.

Had my car out on the track week before last, need to get some time as baskerville to set the suspension up properly though.

who's GC8 you flogging?

Edited by sav man

I'm a fan of not getting arrested. Hence the racetrack, esp this close to Targa the coppas will be on the lookout for Targa recce.

Yeah goes well, very happy with it. I'm surprised how easy it is to drive, the lack of tourqe means it won't spin the wheels unless you clutch it. Got it into the 62's at Symmons, i've put some more boost and timing into it since then. E85 is on the way too.

Great news Ben, how does it go/ Do you like it?

The GC8 is one of Rallyschool's.

What is the go Timmeh?..... engine cactus?

Guru at Fitzgerald's says engine is fine, just head gasket which may have happened when split radiator hose way back at High Country, just wasn't showing up until engine was heat soaked... Find out next weekend when it gets a thrashing.

Cross fingers/Touch wood/pat head/spin around 3 times/throw salt over shoulders.

Otherwise ill let everyone know where the best bonfire is going to happen post Targa!

Well I completed my final shakedown on the weekend and can say this new car is finally pretty good. We found last week a cracked turbo intake pipe which obviously hasn't been helping! No idea how long that had been there because it hadn't been on a dyno since it was first built. We also have finally got the handling balance right so lets bring on Targa!

Less than a month to go!

:)

Good news Snowdaddy! Have we got a confirmed 'crew' yet??

I'm a fan of not getting arrested. Hence the racetrack, esp this close to Targa the coppas will be on the lookout for Targa recce.

Yeah goes well, very happy with it. I'm surprised how easy it is to drive, the lack of tourqe means it won't spin the wheels unless you clutch it. Got it into the 62's at Symmons, i've put some more boost and timing into it since then. E85 is on the way too.

What cops? ours are all in court babysitting criminals. If your smart and recce in a silver falcon, people think you are the cops (as was the case twice during Rally Tas recce!)

i can second that bens new car is easy to drive. its a surprise to us both we havent discovered more faults with it as we are just 2 noobs building a race car from scratch. a few more bits to finish off yet thoe.

if i had of driven at symonds the other weekend i could have nudged a 60. its that easy to drive.

oh and the brakes are unreal for non asisted items.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...