Jump to content
SAU Community

Recommended Posts

it's getting close now, just had my leave approved, and Damo and I will spent the long weekend doing recce.

Had my car out on the track week before last, need to get some time as baskerville to set the suspension up properly though.

who's GC8 you flogging?

Edited by sav man

I'm a fan of not getting arrested. Hence the racetrack, esp this close to Targa the coppas will be on the lookout for Targa recce.

Yeah goes well, very happy with it. I'm surprised how easy it is to drive, the lack of tourqe means it won't spin the wheels unless you clutch it. Got it into the 62's at Symmons, i've put some more boost and timing into it since then. E85 is on the way too.

Great news Ben, how does it go/ Do you like it?

The GC8 is one of Rallyschool's.

What is the go Timmeh?..... engine cactus?

Guru at Fitzgerald's says engine is fine, just head gasket which may have happened when split radiator hose way back at High Country, just wasn't showing up until engine was heat soaked... Find out next weekend when it gets a thrashing.

Cross fingers/Touch wood/pat head/spin around 3 times/throw salt over shoulders.

Otherwise ill let everyone know where the best bonfire is going to happen post Targa!

Well I completed my final shakedown on the weekend and can say this new car is finally pretty good. We found last week a cracked turbo intake pipe which obviously hasn't been helping! No idea how long that had been there because it hadn't been on a dyno since it was first built. We also have finally got the handling balance right so lets bring on Targa!

Less than a month to go!

:)

Good news Snowdaddy! Have we got a confirmed 'crew' yet??

I'm a fan of not getting arrested. Hence the racetrack, esp this close to Targa the coppas will be on the lookout for Targa recce.

Yeah goes well, very happy with it. I'm surprised how easy it is to drive, the lack of tourqe means it won't spin the wheels unless you clutch it. Got it into the 62's at Symmons, i've put some more boost and timing into it since then. E85 is on the way too.

What cops? ours are all in court babysitting criminals. If your smart and recce in a silver falcon, people think you are the cops (as was the case twice during Rally Tas recce!)

i can second that bens new car is easy to drive. its a surprise to us both we havent discovered more faults with it as we are just 2 noobs building a race car from scratch. a few more bits to finish off yet thoe.

if i had of driven at symonds the other weekend i could have nudged a 60. its that easy to drive.

oh and the brakes are unreal for non asisted items.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
×
×
  • Create New...