Jump to content
SAU Community

Recommended Posts

Just get it rego'd in tassie as SI on a rally log book and you don't have to worry about complied.

I don't know that its a huge job to convert a non-abs to abs since the ACD uses the abs sensors for wheels speed, so they already have that part covered.

Yeh I was pretty certain the cutoff year was and would be for the forseable future 2002, not sure where the idea that it increases every year came from.

That said VII it is?

Probably not ideal for tarmac but this is pretty damn cool, might see it at the Burger ring in June yet!

Lexus-IS-F-CCS-R-on-2011-Tokyo-Auto-Salon-front-side-view.jpg

WTF is that Timmay? A Subaru or something? It's icky :P

Yeah a 7 is the cutoff I believe..... not sure where the rolling year idea came from, maybe from Gus who was planning on running his Spec C in EM once it was elligible?

worse than a subie, it's a expensive toyota.

You can chuck the good ol commodore abs unit resnobly easy if you get a non abs model.

You would pick up an emo abs unit that would just fit too, plenty around.

Retro fitting the ABS can be a right pain in the arse. The hubs on the RS dont have the hole in them to fit the speed sensor so you need for hubs. The driveshafts dont have the ABS gear on them so you need to replace them. Then you need the AYC ECU and the yaw sensors and then figure out how to wire it up. :)

Preference would definately be to have one already equipped.

Glad to hear the date isnt shifting. After looking into classics Stu advised that the date after being shifted to 1985, is likely to stay that way for some time to avoid the goalposts consistently shifting as to what is the best car to be in. Would have hoped they were doing a similar thing for EM. I guess a revision about once every 10 years would make sense. Apparently it was about 15 years before classic got revised from 1980 to 85.

So a VII would be the pick out of the EMO range. Or really, get an 8MR RS and despec it to be a VII. The precedent has been set. :)

The RS has proper mechanical diff in the rear, the actual change is quite a lot from a GSR, you have to change basically the majority of the rear subframe, diff housing, axles, tailshaft and centre diff.

As this is what we did to Millars old IX.

True, precedent set ;)

What is the advantage besides an alloy roof?

To be honest Woo I am not quite sure on all of it. It was mainly the ali roof, slightly updated ACD software (they are reflashing the factory ACD ECU's now so no biggie) the VIII MR had slightly more aggressive cams, (different cam timing stock, same lift and duration) and a different huffer and thats about all I got off the top of my head.

You do pay a bit of a premium for the MR so maybe not worth it for largely a few kgs off the roof.

There were some MR RS's but they were rare as the proverbial. As Tim suggested, doing a GSR to RS conversion can be done but it is a little bit of work. With my TME it was just a RS diff centre, driveshafts and "moustache" (diff support) bar and subframe to do the swap. Tailshaft was sweet. Centre diff was sweet as well.

From my experience, you are best off trying to get as close a spec as you can out of the box rather than arsing around trying to turn something into something its not. A VII RS with ABS would be sweet if they exist, or possibly an 8MR RS if you can find one. Or an VIII RS I guess. Then its just a front bar, bonnet and rear wing essentially and you have a VII.

You would just go a motec diff controller anyway, or a ralliart controller (which I happen to know where there is one sitting :D)

Just not convinced you could take an VIII and run it as a VII just by changing bumpers

So how loose are the rules for Classics up to '85. I had plenty of time whilst waiting by the side of the road and thought of a pretty cheap and fun Classic MS car. Looking at some of the Torana's/ Mustangs I think I could put something through a sausage machine that would be fun and and pretty cheap, that once in a while could be pretty quick :)

And all this talk of Evos must make your vaginas sore? If you need 2L AWD then go R32 GTS-4 baby but seriously...Cossie Escort all the way!!!!! Every 2-3 months I look at all the cool Grp N ones you can buy out of Europe for almost a song. Most LHD but some RHD. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...