Jump to content
SAU Community

Recommended Posts

For those of you who don't know i just picked up series 2 1999 stagea it came with adjustable teins not quite sure which model yet but while the compliancer was doing the roady he found the rear shocks were seized and could not be adjusted the car is stupid low in the front but have been adjusted up to legal but the rear sits lower now cos of no adjustment . I was wondering anywhere in melbourne to get these repaired or can i buy tein rear only from somewhere? Any help greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/
Share on other sites

Thanx for the directions guys found a tein authorised repairer 40 km's from my house which is f$%kin rare when your in central vic, but then again bendigo is the hoon capital of Victoria more cars seized under the new hoon laws than anywhere else in vic not bad cosidering they have a population smaller than geelong. :)

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4013580
Share on other sites

so the shocks aren't seized, it's just the height adjustment?

Any mechanic with half a clue and a set of C spanners should be able to sort it if he has some decent penetrating oil or a big enough hammer.

Yeah just the hieght adjustment part of it

That was my thought but APPARENTLY they will not budge obviously they dont have enough wd40 and big enough hammers in their workshop LOL :)

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4013662
Share on other sites

Well A)I cant get them out myself B) It needs to be done for roadworthy and the compliance shop cant do it. So in order for me to pass roady and get plates the height of the rear needs to be lifted since the jap owner had it stupid low and now it's seized in that position which is about 80mm of the ground.

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4016757
Share on other sites

Well A)I cant get them out myself B) It needs to be done for roadworthy and the compliance shop cant do it. So in order for me to pass roady and get plates the height of the rear needs to be lifted since the jap owner had it stupid low and now it's seized in that position which is about 80mm of the ground.

If its just for roadworthy you've probably got more chance taking the springs out of the car and working on them.

My compliance shop was going to throw away my Ohlins coilovers (ie. >16 way adjustable and good spring rates) because they told me they were "rusted out" (sand blasting fixed the surface rust).

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4018343
Share on other sites

im not sure which state u are in, but height adjustable shocks that allow u to lower the car below stock are against ADR's, they are not legal but u might be able to engineer them which counts for something in some states.

also not to mention the spring rates, im not 100% on this but i beleive u can only increase the spring rate by 75%, im sure someone can correct me if that figure isnt right. AFAIK the teins are a touch below this, even the aus spec ones.

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4022030
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How would you even adjust the clutch if the pedal already has the correct free play? The operating cylinder has no adjustment in mounting position or rod length. On pull style clutches there is also no ability to adjust the bearing carrier. Push type I can see how adjusting the carrier height makes it all work.   If this is the twin plate clutch did you verify that your friction disks were oriented correctly? It's not mentioned in the directions at all you just have to notice that one side the friction disks have a part number on the hub fingers and a subtle coning to those fingers. Another thing that I noticed was if you put the friction disks in backwards the pressure plate fingers will not be even and flat when the clutch is installed.
    • yeah, mechanically, it is probably do-able, off the top of my head, there would be the transfer case, which I believe will bolt up to the rear of the RWD transmission, the shorter rear tail shaft. A front drive shaft, front diff, engine upper sump, front drive shafts, front hubs and front AWD struts (they are shaped around the front drive shafts), LCAs (at the very least from the front suspension) oil cooler.  You might want the rear diff from an AWD too, so you can be certain the front and rear diff rations are identical.  Who knows what brackets and mounts you might need.  So a whole doner car might be the best option if you need to maintain RHD. Then actually making it work, that would be a whole different story.
    • Take the fall as a warning sign for future endeavours  Stay safe mate
    • hi mate, HKS cooler piping still available by any chance?
×
×
  • Create New...