Jump to content
SAU Community

Recommended Posts

  • Replies 144
  • Created
  • Last Reply

Top Posters In This Topic

am looking for the plastic thingy in the middle that goes around the deck/aircon control etc.

how much ? and where can i pick it up if not how much postage to syd 2165..

ohh and do you still have the intercooler ? :)

Omg! now a million dollar question which I forgot to ask.....is it the same asd the R32 GTR one..if it I will take it..

From all the pics i have seen it is. The reservoir is different but the lid looks to be common between the 2

am looking for the plastic thingy in the middle that goes around the deck/aircon control etc.

how much ? and where can i pick it up if not how much postage to syd 2165..

ohh and do you still have the intercooler ? :)

Hi mate,

I have a panel glued to the back of the surround with gauges mounted and will have to see if i can remove it without damage.

Oil cooler sold

GTSt indicators sold

I am removing the engine tomorrow, i started and videoed the engine today prior to removal so if anyone is interested in the engine i can get a copy of the vid over. The car ran for about a minute before being shut off and idled surprisingly well considering the hole in the intercooler end tank which we found later.

I also carried out a compression test about 5 minutes after taking the video

1) 150psi

2) 152psi

3) 151psi

4) 150psi

5) 150psi

6) 150psi

I was pretty surprised by the results as i have never tested an engine with such consistent compression.

So splitfires and injectors are now available

engine and box are now out of the car.

Passenger side caster rod was found to have a slight bend as seen in the attached photo so price is reduced to $75. It's probably still usable, the threads are fine, ball joints fine so if anyone wants to have a punt, $75 firm or i keep em for bits.

post-2863-1217150516_thumb.jpg

Also pics of some of the other bits i am getting questions about.

post-2863-1217150798_thumb.jpgpost-2863-1217150821_thumb.jpg

post-2863-1217150854_thumb.jpgpost-2863-1217150878_thumb.jpg

post-2863-1217150919_thumb.jpgpost-2863-1217151121_thumb.jpg

post-2863-1217151220_thumb.jpg

gear box cross member was found to be bent. Now separating the box, tailshaft and modded speedo drive

rb25det box $1350

1 piece custom Hardy Spicer tailshaft $350

gtr speedo drive with r33 gear $50

I also have a brand new navara speedo drive i think it still has the original gear on it $50 as well.

gear box cross member was found to be bent. Now separating the box, tailshaft and modded speedo drive

rb25det box $1350

1 piece custom Hardy Spicer tailshaft $350

gtr speedo drive with r33 gear $50

I also have a brand new navara speedo drive i think it still has the original gear on it $50 as well.

Hey mate,

Speedo drive SOLD

Check your PM

Cheers.

i have a stock one but it is far from good. I'm keeping my aftermarket one on the off chance i buy a new car that it suits.

If you need it anyway send me a pm and we can talk price.

now separating the cams, cam gear and engine. I'll remove them from the engine this weekend and reinstall stock cams and cam gear

so early hks rb25det cams 256 8.8/264 9.0 $650. If i find i have a spare stock exhaust wheel i'll chuck in the adjustable one at that price

s1 rb25, no coils, no turbo and a set of stock injectors and a rail. sump has a dent in it where it hit the sway bar but can provide a spare, runs well, good compression $1350

Edited by BHDave

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...