Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

if you could get a quote for a s/s version to suit a r34 (would have it in a simular location to where yours is), with the speedflow fittings i would be keen. I believe you that there hasnt been any problems, i'd just rather have peice of mind when i'm booting the shit out of it, knowing that there is no way main oil lines will be leaking/popping off.

Also, could the thermostat be intergrated into the s/s line?

:(

yeah the thermostat can still be used, just means another 4 fittings.

fair enough for wanting peace of mind, it just costs a bit more

im going to have a sus on exact pricing on monday.

how much for just the oil cooler core only ?

pm sent

would this fit a 7mgte / 7mge (from ma70 supra) also interested in speedflow fittings

yeah, it definitely fits the block.

NOW for the few people who are interested in the braided line version with speedflow fittings (blue and red anodised alloy) it will cost another 150-170 on top of each kit price. (not including the thermostat.) That is IF there are a few people who are interested in the kit with the braided line and fittings.

The braided hose itself is actually of a larger diameter also which means less restriction on the system.

So we're looking at around $550-$570 including the braided lines, speedflow fittings and thermostat?

I may be interested. Need to measure if the core will fit in the front of my Stagea somewhere.

I'm interested in an oil cooler with thermostat and speedflow fittings.

+1 definately interested in the whole lot

how many people did you need for the braided version to go ahead?

So we're looking at around $550-$570 including the braided lines, speedflow fittings and thermostat?

I may be interested. Need to measure if the core will fit in the front of my Stagea somewhere.

incorrect. another 4 fittings and 4 adapters are needed for the thermostat.

the kit will be 2nd to none though, with every component being the best you can get.

I'm interested in an oil cooler with thermostat and speedflow fittings.

interested as in deposit interested?

+1 definately interested in the whole lot

how many people did you need for the braided version to go ahead?

3 deposits of say $80 will get it rolling. 1/2 week turnover.

this whole kit needs to be revised if there is CERTAINTY for the braided version with necessary fittings.

the first quote was for 3.5M of braided hose.

if you measure how much hose you require in TOTAL i can adjust kits to suit.

PLEASE DISCUSS, because the fine details are important.

I'm looking at mounting the oil cooler where the SMIC is. (Will be changed to FMIC of course) So if you could allow for that length. 3.5m should cover it I would think.

this whole kit needs to be revised if there is CERTAINTY for the braided version with necessary fittings.

the first quote was for 3.5M of braided hose.

if you measure how much hose you require in TOTAL i can adjust kits to suit.

PLEASE DISCUSS, because the fine details are important.

if you copied a simular length to what you have in your car, but just in braided line and the provision for the thermostat that should work well. Most people would have it in a simular location to where yours is.

You can definately add me as apart of the group of 3, as soon as 2 other people show interest in the same kit i dont mind putting $80 deposit

:P

if you copied a simular length to what you have in your car, but just in braided line and the provision for the thermostat that should work well. Most people would have it in a simular location to where yours is.

You can definately add me as apart of the group of 3, as soon as 2 other people show interest in the same kit i dont mind putting $80 deposit

:P

I'm sweet for a deposit too.

Hey mate,

Interetsed, but can you please confirm price for full kit, with braided lines long enough to mount on the passenger side of a 32GTR?

Whats the actual size of the core, (Dimensions)

is there any chance of buying the speedflow fittings and ss braided hose by itself?

i'm quite keen as i have a similar setup using the permacool and b&m thermostat with a sertrab core

i'm yet to be install the kit on the car,

and i have always been a little concerned about the rubber hose that is supplied kinking and then restricting the oil flow...

pm me if possible,

thanks,

greg-

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...