Jump to content
SAU Community

Recommended Posts

The problem with streaking all comes down to what rag/cloth you are using.

Gotta use rags that feel really dry and rough (towels, flannelet etc)

not smooth or soft...

Best method i have found is.....

Use 2 rags, spray glass and wipe with first rag till most of window cleaner gone...doesn't have to be perfect then spray the glass again but a bit less and wipe with second rag until dry and all streaks gone.

the more dry your rags are the better the result

:(

All of the above works but if you want it looking really wicked then let whatever you have used fully dry, then get yourself one of those microfibre dust cloths (got mine in a $2 shop for... $2 :) ) It also works really wicked on your paint work, makes it come up as if you had it cut and polished, everything needs to be completely dry to do it properly. I have one for my windows, one for the paint work and one for the mags :P

very mild soapy water on window tint only I wouldn't trust anyhting else, especially if you don't know what quality tinting film you have..

+1 for newspaper and vinegar...

Although after washing my car I usually stop by the servo and use their paper towels and if your careful you don't get the lint effect...

i use this window cleaning foam and a special square like pillow made for cleaning car windows it is soft but slightly Abrasive after i rub the foam of with it i go over it with a micro fibre cloth. After that they are pretty much crystal.

Oh and i got both products from supercheap auto.

Edited by phenline

phenline i think i have both the products you are talking about! i found the spray worked awsome sometimes and others it streaked really bad...figured i was using to much of it. I may have to try it with a 2nd cloth to wipe at the end and see how i go.

In regards to metho i think it stuffed my rear window tint(old man put it in my washer bottle) the tint likes whiteish from the inside but i noticed it not long after i got the car so i dont know if it was like it when i got it.

is metho bad for window tint?
phenline i think i have both the products you are talking about! i found the spray worked awsome sometimes and others it streaked really bad...figured i was using to much of it. I may have to try it with a 2nd cloth to wipe at the end and see how i go.

In regards to metho i think it stuffed my rear window tint(old man put it in my washer bottle) the tint likes whiteish from the inside but i noticed it not long after i got the car so i dont know if it was like it when i got it.

Metho is a window cleaner, as I read last time.

But I would not use it on your window tint.

I ment clean the outside of the windows with metho don't rub it in on the inside where your tint is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
    • Mine's a bit bigger at 70x150mm roughly. The spots are flat, just can feel the edges if I dig my nail into it. I did fix some other other ones by both using my finger to sand that small spot (I'm a bit wary of doing this and creating hot spots and a bigger mess) and I also did sand over it flat and others, but this also worried me a bit because if I create an overall low spot on the panel on paint that is good.  Correct me if I'm wrong but as long as it's flat even if I can feel the edges, I can put filler because it will all be level once I sand it? I can see myself going in a circle after sanding guidecoat with 320 grit if for example the panel is flat with my hand but because I sanded the guidecoat I could have created a low spot again somewhere. Unless where I'm going wrong is what I mentioned previously where I didn't go low enough on the grits. It's 1 step forward and 2 step backwards here haha. I'll probably need to experiment with it more. Last time I go back to bare metal lol.
×
×
  • Create New...