Jump to content
SAU Community

Recommended Posts

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/
Share on other sites

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

not really much difference aslong as everything has been fixed/changed at the 100,000km service point. its only another 100,000km service pretty much. obviously at that age a compression test should be done but you should do that at the 100km aswell.

if it has been looked after there i don't see a problem. maybe all fuel lines, vacuum hoses etc should be checked and replaced if you haven't done so.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4032667
Share on other sites

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

you should replace some of the ignition parts...i.e. coils, if you haven't replaced them yet, they start failing around the 200k mark...also check some of the electronics, i.e., water pumps.

have u ever gotten a carbon flush? if it hasn't been done on your car for a while then have it done, it just removes excess carbon build up in the engine.

I'm not an owner but my mums car ('94 bluebird SSS) recently got a 200k service and that's some of the extra things the mechanic replaced.

Edited by INTNS
Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4032713
Share on other sites

the servicable items are all the same, except it is recommended to replace timing belt idler and tensioner, tensioner stud & bolt, timing case seals & water pump in the front. everything else is per usual. i would not go changing coils unless you have an issue. Get a diagnostic done to check sensor operation.

Hey all,

My 94 r33 gts-t Skyline is coming up to to its 200,000KM mark and was wondering do I need to get anything different done then a 100,000KM service?

And also if it is "worth" trying to add on more performance modifications if the KM's are this high.

I'm a car noob so please don't hurt me. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4032762
Share on other sites

depends on whats been done and what condition your cars in.

My '93 r33's coming up to its 190,000km birthday and still kicks ass.

Getting the timing belt done on monday, $980... Coils were replaced last service 185,000kms.Exhaust gaskets are getting a bit leaky so they'll be replaced too soon.

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4038463
Share on other sites

all it has done is heavy duty clutch, fmic, pod filter, atmos bov.

as for its condition the last time i got it serviced at xspeed the only thing they said was the rocker cover was leaking, although im not sure if they did a good job, they seemed a bit flaky...

I've noticed no problems driving apart from the usual atmospheric bov + gts-t stalling issue.

@grubb which timing kit?

thanks for the help

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4039478
Share on other sites

  • 3 weeks later...

The 200,000km service is a major, just as the 100,000km. On the engine side of things, the major components are:

  • Timing Belt
  • Timing Belt Bearings
  • Water Pump

I offer kits, that include genuine Nissan or OEM parts, and can be found within the following link:

http://www.skylinesaustralia.com/forums/Ni...vi-t137554.html

Link to comment
https://www.sau.com.au/forums/topic/229387-200k-service/#findComment-4079574
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...