Jump to content
SAU Community

I'm Goin For A Drive *sunday 7th September*


  

28 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

I've been wanting to organise this for a while so finally pulling my finger out.

The date is Sunday the 7th of September

Ok, so Meeting at Old Parliament House in the morning so we can leave at 9:30

From there we'll head out to Uriarra Crossing, than down to the Cotter, than head south to the Corin Dam. From there, back onto Tidbinbilla Road, down through Tharwa and (my favourite bit) up to the old tracking station at the end of Apollo Road. Finally finish up at Point Hut Crossing.

Here's a map: http://maps.google.com.au/maps/ms?hl=en&am...615234&z=11

If anyone's interested, we can organise a BBQ or just drinks to put some more cash towards the banner. Or we can go to have lunch somewhere.

We'll be stopping at at least four places so there'll be planty of opportunities to take photos.

If anyone hasn't been out that way before, I've done this route lots of times on motorbikes and a few times with a car and it is lots of fun so if you're borred of driving from one traffic light to another I guarantee you'll enjoy this. The roads are good and if we go in the morning, traffic is usually minimal.

Cheers

Tarmac-

  • Replies 186
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

7th would be better cos there's that motorkhana on the 24th... seems to suit most ppl anyway..

I'd love to come but it's a bit too early for me lol, I had enough trouble making 1pm (as everybody knows :ermm: )

It's looking more and more like the 7th.

So the list:

Tarmac-

Ex!$t3nZ

Bluprint

datto260Z

Gus-

CeJay

INVRTD

Frink

Come on Shel, stop being so soft, you know you want to come :thumbsup:

Ps: it doesn't matter what car you come in, even a Datto 260Z will be ok although I'm yet to be convinced that it exists :ermm: having said that, open wheelers should probly be left at home

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...