Jump to content
SAU Community

Recommended Posts

Hey Guys,

I have a 92 N1 GTR and was thinking on popping in a GREX oil cooler kit. However I have been reading that the N1's came with an upgraded oil cooler.

Can anyone confirm this? Where is it located?

I want to do a bit of track work, and was wondering if it's necessary to to upgrade to the GREX kit?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/
Share on other sites

Have a look around the radiator, my guess is that it would be around there

Give it a bit of stick down old pac one day soon and keep an eye on the temps - that should give you an indication :D As a reference, my old setup with no cooler would hit 130degrees with ease on old pac doing the uphill section

I am BUSTING to have a look at your new car mate - Coming to any club events soon?

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4121498
Share on other sites

Thanks Steve,

I'm busting to get to an event :-)

Hopefully the upcoming cruise, if all goes well.

I'll have a look around the radiator tonight when i get home.

I haven't given it too much so far (have hardly driven it!) but I'm yet to see oil temps over 90 (on the stock guage).

I was going to do the cooler this weekend and take it from there.

To be honest, I'm getting the GREX kit from a mate for $300 so may just do it anyway. Will give me even more track days in 40degree Wakie summer heat.

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4121527
Share on other sites

Thanks guys.

I may have missed out, or they could have only came on the second series of R32 N1's (V-spec's) cause I can't find anything.

Unless I'm completely blind (which is possible).

I've checked infront of the rad. and in the front bar on both sides in front of the wheel wells and nothing that i can see.

Ryan, if I find a cooler already on mine, no drama's.

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4121854
Share on other sites

I'm not sure where the standard n1 32 cooler sits, the only way to confirm is to look for 2 oil lines coming from a sandwich plate under the oil filter. I'll try and dig the pics out of fast - either post or pm me your vin and i will look it up

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4122505
Share on other sites

Is it this exact oil cooler that nissan want a crazy amount of dollars for or is it the later model N1 coolers?

I think they want crazy amounts for both mate.

Hopefully I've just missed it and there is one on the car.

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4122914
Share on other sites

thanks buddy,

Not to fussed if it isn't cause $300 for the GREX kit including filter relocator in virtually brand new cond. aint that bad. It's just the hassle of fitting it :-)

A mate who's gone a big single on a 32 GTR bought the GREX kit which had a couple of thousand k's on it, but then decided to go brand new as it was pretty much the only second hand part on the engine build.

On a side note, he fired it up last week for the first time and put out a nice 430kw at the rears only.

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4123080
Share on other sites

Thanks Duncan,

I'm going to take the front bar off this weekend and see what I can find. You'd imagine that something that size should be visible but I couldn't see anything.

I'll see how i go.

Don't take the bloody front bar off you goon! :) Have a look at the oil filter area and look for two hoses of 2-3cm diameter coming out from a sandwich plate (about 2-3cm thick) sitting between the oil filter and the block. If you find the hoses, follow them down the yellow brick road to nirvana.

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4124905
Share on other sites

If you dont use your mates cooler set up may i purchase it :)
Nice power! PM Sent btw

$300 for that? ill give you $400 for it, today! Unless someone has already got in for it :P

you are one of a kind steve-o.... nice way to bogart the purchase there. nono.gif

Link to comment
https://www.sau.com.au/forums/topic/235355-n1-oil-cooler/#findComment-4125033
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...