Jump to content
SAU Community

Recommended Posts

I am looking at buying a 1996 R-33 automatic, Turbo. Was wondering whats the fuel consumption of these cars? The owner said 10l/ 100 km. Im a newbie at skylines and cars in general and please dont start stoning me cause its automatic, I know manual is better but for me this car will suffice.

Edited by LightninG
Link to comment
https://www.sau.com.au/forums/topic/235557-r-33-auto-turbo-petrol-consumption/
Share on other sites

I believe its stock, just has turbo.

Also would getting rid of the turbo be a good idea since im on my provisional licence and I can't drive turbo charged vehicles. How would that affect the car? I was thinking of just driving it with turbo and hoping not to be stopped by police.

Edited by LightninG

hey mate,

i have a 96' r33 turbo thats auto for sale. depending on how i drive i can get 400kms or a bit more out of a full tank. its on carsales if u wanna have a look, my rego is BLKAZN, trust me u wont be dissapointed. shes imaculate. u can quite easly get away with driving her with out getting pulled over, shes a sleeper. we can work something out if ur interested in buying her. hope to hear from ya...

has no one mentioned that you cannot even register it as the transport in ur state won't let a turbo car be registered in ur name..

and it's not just a matter of taking the turbo off.. just get a shit box or get a non turbo if u insist on a skyline until ur opens.. if u can avoid rbt.. random pull overs.. speeding.. cranky cops.. for ur 'P' period i'd consider you lucky

400km out of a tank with a catback and pod. not being very gentle with her either.

dont buy the turbo if you are under the new scheme. you will get reamed. and its not a simple thing to just take the turbo off either. an RB25DET (turbo engine) will be slower and more sluggish without a turbo than an RB25DE (nonturbo engine). get a non turbo r34 sedan or something. very good cars for a similar price. upgrade to a turbo later. by the time u get off your p's, a lot of cars woulda dropped in price too which is a bonus

Thnx for responses. I am not sure what Im gonna do. The car that I found is very cheap for the condition that its in. 10 000 very well looked after, 96 R -33 turbo auto. I can probably go for my manual licence and then look for a manual R-33 non turbo, but I dont know if Ill be able to find one for around 10k in good condition.

And yea, I just asked what the penalties are for being caught driving a turbo on provisional licence: 3 points and $220. Definitely not worth it.

One last question; If I do take out the turbo and put it back in 2 years time when I have my open licence, would it still be the same performance, like would the actual taking the turbo out then putting it back reduce performance?

Also how much would it cost to take out the turbo?

I love metaphors so-

pretend the skyline turbo/you are/is a level 99 magician. By taking the turbo off you then reduce it/you a level 9 peasant with spells disabled and no artifacts. Now you are still are a magician at heart and the policing force of Nurcramancers will be able to detect your level 99 magician skills but sadly they do not know nor care your a level 9 peasant and will destroy you with a 90 attack point spell (most likely lighting or something similar). In the end you and your car will have a horrible death.

TRANSLATION: Your car will still be registered as a turbo and the PO-PO will see this and kick you in the dick. They won't care if you have taken the turbo off or not. I doubt you'll even be able to register it in your name. Now, even if you were to avaid the police in a level 99 magic.... I mean turbo skyline the cost of getting someone to take a turbo off a turbo engine and getting it to run right would scare you and be very pointless when shown the direct comparison of just buying a non-turbo skyline. If you can't find a manual no-turbo r33 for under $10,000 you need to look harder.

Hope this helps without scaring you too much.

Edited by gunmetalgrey

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...