Jump to content
SAU Community

Recommended Posts

IM buying an R33 from a dealer (have my reasons) and wanted to know if there are any major things i should look at it the R33 GTS25T Model and it will either be series 1 or 2.

Thanks

Also what would be the recomended coulour i am leading towards the metalic grey or silver..

Thanks

The Series 1 front lights tend to haze over so that may just be a little reason to choose a Series 2 so you don't have to change your front lights out. I'm not sure if that's normal for 'all' Series 1's but a couple of my friends have had to change them out. Good luck.

Originally posted by sewid

heh if your friends bought new lights because they "hazed" then they wasted a lot of money. You can clean that with any decent cut/polish.

If I were you I would lean towards the S2 simply because it's newer.

Yeah, that's what I told them because my civic lights hazed over and that's what I did but theirs were fogged on the inside. They cleaned the insides and resealed them but I don't think they sealed them correctly.

Rust more Rust and More Rust,,,depending on where the car lived in Japan,,,,they use salt to break up the snow. Check the boot area both inside and out. Remove the boot trims and have a good look/feel around. Also check up underneath all 4 guards and make sure it's all clean. Check for accident damage,,look at all the hinges and there bolts to see if a snappers been on them and removed some of the paint. Really you should have a good Mechanic and a Panel Beater/Painter/Detailer with you because these guy's know cars.

Neil.

Originally posted by ndr

Rust more Rust and More Rust,,,depending on where the car lived in Japan,,,,they use salt to break up the snow. Check the boot area both inside and out. Remove the boot trims and have a good look/feel around. Also check up underneath all 4 guards and make sure it's all clean. Check for accident damage,,look at all the hinges and there bolts to see if a snappers been on them and removed some of the paint. Really you should have a good Mechanic and a Panel Beater/Painter/Detailer with you because these guy's know cars.  

Neil.

i have imported ,maybe 100 r33s and i have never seen rust,a few r32s with rust,but never r33

Originally posted by vspecv

i have imported ,maybe 100 r33s and i have never seen rust,a few r32s with rust,but never r33

Lucky you,,,I have seen rust,,,both in the boot area where the boot floor meets the rear 1/4 panel extentions and up under the rear wheel arches.

Neil.

Check for rust even on a 33. It does happen sometimes. I've got a tiny bit of surface/bubble rust around my left rear passenger window, as well as some light surface rust around the bolts that hold the front guards on. I don't think it's anything to worry about for 5 years or more since I keep it garaged, but I think before then I should be looking at rust proofing it somehow. Check for any repaired crash damage, as these areas tend to rust up quicker.

As for the mechanicals, check for gearbox and clutch problems, plus the usual stuff like worn rings (blue/white smoke). They will blow a lot of black/brown smoke naturally because they run rich, so don't worry about that.

Silver or grey are good low maintenance colours because dirt doesn't show up on them easily (silver's a bit better for hiding dirt). I prefer black myself, but it gets dirty very quickly. If you like silver best then I would say to get silver.

Originally posted by vspecv

i have imported ,maybe 100 r33s and i have never seen rust,a few r32s with rust,but never r33

I saw 3 r33's with rust when I was looking for mine... Two had rust in the boot and one had some in the engine bay...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...