Jump to content
SAU Community

Recommended Posts

Here is one to stir the pot.

I'd like to hear what people think on the idea that your age should restrict you in vehicle power.....

Example......

Should people now entering their P plate's be able to drive V8's or Turbo's??

Would Govt restriction's slow or stop some people killing themselve's in high powered car's when they dont really know how to handle/drive properly.

What age do you think people should be able to buy/drive high powered car's

........

Im not out to say anything bad about different driver's..... im interested in what people think

Loz

Link to comment
https://www.sau.com.au/forums/topic/23830-age-power-restriction/
Share on other sites

I've said this over and over.

The only way to stop so many young drivers from causing accidents is EDUCATION!!!

put them through driver training as a pre-req for getting ur P's. put them through all conditions in a closed environment (i.e. skidpan) to learn how the car responds to different conditions..

The only way to stop these accidents is making sure that when things go pear shaped, these people know how to respond and avoid fatality.

to me a power restriction wont be as effective as you'll still lose a Toyota Echo in the wet if u dont know how to handle the car...

The best thing to ever happen to me was when I moved into a powerful car.

280rwkw is a lot to handle, and it teaches you to be EXTREMELY careful where, and when to plant that throttle.

Before, I had slower cars (Mazda Astina V6, Proton GTi, etc) and I found myself wringing the neck out of those bastards because I had something to prove... Nearly every traffic light I'd take off with vigour.

When I moved into the Skylines, I had nothing to prove, and my driving became much more sensible and mature.

Racktrack experience also helped more than I can stress, because it shows you the limits of your car, and when happens when you exceed those limits.

I agree with Tosh in that much more driver training is needed to gain your drivers licence. Did you know you could easily get your P's without ever driving in the rain or at night? That's utterly ridiculous.

Also, I took my driving test in an automatic. My Learners and Provisional licences were restricted to automatic cars only, but as soon as I got my Silver Licence, they removed that restriction. Apparently driving an automatic car for 2 years gives you the ability to drive manual cars ;)

Nothing beats experience and that's what Learner driver training should give you. At the moment, it doesn't give you sh1t.

I think you need to learn to swin before being thrown in the deep end.

I am glad I did not have a powerful car when I was on my P's. By the end of it I was driving a V6 commodore which had enough power to get you into trouble/danger.

I agree with Merli that you become more sensible over time, you've got to build up to these things. If you've just started driving, in my opinion, a Skyline, or any other relatively high powered vehicle, is not the car for you. Not only do you lack the experience in situations that you have not encountered, in many cases there is a fair bit of attitude in having something to prove.

Tosh, true you could lose it in a Toyota Echo, but put the same person in a car with tripple the power output, a non linear power curve, mix this with the lack of experience in certain situations on our 'roads'* and you've got a dangerous ****tail.

My opinion is based on nothing but my own experiences. It pissed me off no end having to wait for a decent car, but I've got no regrets about the way its worked out :P

At least, in general, those who want to buy a performance vehicle know how to look after it, and do go to lengths to learn how to drive. I'd say most people out there travel on the roads to commute. I saw Australias worst driver. Those people are out there... yet nobody does anything about them :crazy:

* (thats something else all together... not only is the licencing system inefficent, but we get to drive on fantastic quality roads..)

my 1st car was and still is a turbo r33 and i know that if i be stupid its gonna stuff me up bad, but its true any car can kill u, unfortunately 6 months ago my mate died in an accident when he was drivin his crx a bit too quick, and that made me realise to be more careful. but i agree with the driver training thing like

SW20-GT said, if u get to know ur car and how it moves in certain situations it is a great advantage...

cheers...ben.

My first car was a V8 and my 2nd a turbo, and i had no problems in either of them, sure i was picked up by the cops every weekend while driving, P plates stand out like that. but the thing about driver training is a good on, i had it unofficially in my paddock until i turned 17, and i learned how to control the car that much more. people who freak out when its raining or night or busy need to get something done, they're the ones who cause accidents, and training at a young age is the only way to get it to stick in my book

here in meblourne we hav the power to weight rule limiting a p plater from driving any car wif 125KW @ the wheels. the r33 is above this by bout 3 or 4 KW. but still i c p platers driving wrxs, r33s, 180s, 200s, even a yellow lambo at auto saloon.... im turning 18 in 2 months, i will either by a r33 S2, 200sx or 180 afta i get about 3 or more months expierence wif my current car. the rule doesnt bother me as it is bs and is not enforced(most of the time anyway). if it does get enforced i will probably move interstate. in theory aiight it seems like a good rule but fast cars will only b fast when they r PUSHED, i currently hav a 2L celica and for a NA it does go aiight, it dont matta wat car u driving but the ego u hav. u c many accidents wif cars being wrapped around poles but when u think bout it was the driver driving sensibly? i think the death toll will unfortunatly b less then it is, the govt is beating a dead horse by lowering speed limits etc. people will die on the roads, anywhere in the world. in other countries u can go 300Km on the freeway so i think the rules r strict enough here

Staunch: im insured with suncorp metway, but its used as a car for my parents business, it was virtually impossible for us to get a decent quote if we privatley insured the car and i think the cheapest quote we got was 6650 from just cars, and at least they gave us a quote, not many companies accepted us since my age, again with registration it all came easier due to that fact, if u need any more info jus pm me and ill be happy to explain other things...

Terminal: i agree 100%, some of the ppl i seen driving when its raining n shit drive so cautiously its beyond the joke, of course u slow down if its pretty dangerous but i seen ppl on a freeway panic so much when they drive there bound to cause an accident..those are the ones authorities should worry about...

thanx...ben.

In Victoria the cops don't care about the power to weight ratio unless ur in a V8. I've seen P Platers in r33's 34's some GTR's STi's and EVO's. The matter of the fact is, there is a loop hole. The cops will stop a P plater in a V8 (about the power-weight rule), but not in a little jap econo box that would eat the V8 and spit it out.......Thank God.

As I have said before, I agree with what tosh said.... but I still think power/weight restrictions should apply... at least for red P platers...

I have seen so many P platers driving dangerously (not just dangerous to themselves, but to others) in powerful cars and it is just wrong. Nobody that has only been driving for a year of less would have enough experience to be able to handle a big car (say v8 for example) safely.

Fair enough there is possibly exceptions to this but in most cases I think it would be true.

Merli got it spot on.

My first car was an Auto Pulsar, and I drove it hard. Then I got a 99 celica and drove that hard. Both of those cars where not powerfull, so you push them alot harder.

I started to do some driver training in the celica and realised how easy I could get into trouble. I learned how to start to handle a car which was out of control. (Well getting it back anyway).

After that my driving has gotten alot better, I have not had a speeding fine since and I drive alot more carefull in the skyline. I respect that my car whilst not a huge KW beast (yet) is still a fast car, and should be respected.

Trackdays are fantastic too, I have learned so much about driving this year, and I am more confident about driving on the road. However there is still the other people on the road to worry about.

I almost had a lady in a Lotus Elise smash into my car the other day on epping road. I had to brake hard and did so very smoothly and pulled up in time. She was not watching and slammed the brakes, now if you lock up a car your not going to stop in a hurry. Needless to say I was worried about this lady and her car becoming a fixture of my skyline.

I think education is a point which needs to be pushed, and we are all capable of this. My sister is going to start to drive shortly and I will teach her all that I know. Then I will pay for her to go to do Level 1 and 2 advanced driving with Aaron McGill. Driving training costs less than most of us pay for insurance, and has a greater potential to safe your life, someone elses life or your property.

ok lets clear a few things up..

here in meblourne we hav the power to weight rule limiting a p plater from driving any car wif 125KW @ the wheels.

this is not correct.

a p plater can drive a car which is 125 kw at the wheels?? the actual rule is a p plater cannot drive a car which has more then 125kw(engine) per tonne of weight.

and secondly

In Victoria the cops don't care about the power to weight ratio unless ur in a V8. I've seen P Platers in r33's 34's some GTR's STi's and EVO's. The matter of the fact is, there is a loop hole. The cops will stop a P plater in a V8 (about the power-weight rule), but not in a little jap econo box that would eat the V8 and spit it out.......Thank God.

sorry dude, this is the biggest bit of bs i have read in a long time.... i think you may have it the wrong way around. a couple of months ago the police were out to get modified and p platers driving powerful cars eg: japanese cars....

corrections made :)

yeh but would u say it is enforced FULLY? if it was the govt would b even richer. if the cops wanted to they could b real pricks and give p platers a 105$ fine for simply driving a car deemed too powerful. and believe me i know alot of people who own r33s 180s, SS's, supra TT RZ and when i ask em if they ever been hassled by the cops bout the power to weight rule i hav to explain to them wat it is. most of em havent even been defected or even pulled over more then once or twice and they r on their Ps.

dude, you didnt even know what the rule was, trust me if cops spot you especially at night you will most likely be pulled over unless they have another job which takes priority.

your friends are just lucky for not getting pulled over.

read the forums, why most people dont like the police, especially why p platers dont like the police...

sorry dude, this is the biggest bit of bs i have read in a long time.... i think you may have it the wrong way around. a couple of months ago the police were out to get modified and p platers driving powerful cars

Mate, I'm a plater I should know. If u drive a V6, and the P plater next to u is in a V8, the cops will always stop the V8. i agree with redline2003. Yes they will stop Jap cars, but not all the time at night. U describe it as if u cannot get from Point A to Point B without being hassled. There are not enough police, or resources to pull off such a feat. Please, stop being so self-righteous, unfortunately, u cannot always be right.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...