Jump to content
SAU Community

Recommended Posts

heres pic of mine, very ricey for some lol floor is getting done in 2 weeks

There is a difference between "ricey" and "Leb-spec".

You sir, are one more re-trim away from being the Major of Beirut.

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

didnt kno 2 seat rego was cheaper...god dammit! 3 years driving round with 6 point cage and intrusion bars, not once had i been asked about it. recently pulled front section out, half cage now remains, was finally fed up looking like i was climbing a jungle gym everytime i got in or out...

  • 3 weeks later...
Sure did :down:

Just going back to the cage, would this be CAMS approved? I seem to remember CAMS only allows two bends in each corner bar for structural reasons? (Yes I can't be bothered looking at my CAMS manual)

that cage design is not CAMS compliant.

  • 2 weeks later...

dahtone, u got any pics of new interior? jus cause u said that the pic is old interior.

and i finally have some pics ot post up!

shit pics but jus took some quick ones after install. will have to get some better pics.

post-53838-1236683755_thumb.jpgpost-53838-1236683770_thumb.jpg

  • 2 weeks later...

Hey guys, a mate and I have just started our own trim shop called Elite Custom Interiors, been working on Summernats and Autosalon cars for 6 years and have taken out plenty of awards at both shows.

If anyone would like any work done give me (Scott) a call on 0403317457 for a quote.

Heres a link to our Facebook group with some photos of our work.

Elite Custom Interiors

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...