Jump to content
SAU Community

Group Buy: R33 Gtst And R34 Gtt Cold Air Box Cover


Recommended Posts

  • Replies 211
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

still waiting on mine also

wont stress to much till friday or so, im probably a bit further away then most people lol

haha try being in Perth..:down:

yeah I'm giving it till Friday or so too, should be good no rush anyways..

Edited by viet_boi

dang sorry guys didnt know it would take this log.

but if any one is NSW wants a box that has holes cut out already for a FMIC dori32 has a box which i sent up in error. no wait just pay him the cash and pick it up.

dori32 i ave a new box on its way for ya tomorow

Yep pretty straight forward.. although the top pipe (factory cooler piping setup) was a little hard to get right, i ended up doing a right royal mash of a job on that one lol.

+1, had to make that bigger, and afm would fit through the hole either, had to file that out. doesn't sit perfect, but im going to make it work. Cheers Ash

Just got mine now

looks pretty good :(

is someone doing instructions for these?they dont look to hard but always helps to know wat your doing

the only problem i can see with mine is that my afm seems to be mounted a bit to far towards the engine so that may have to be moved or the box adapted but other then that looks fine :)

wanna say a big thanks to Ash for setting up this group buy.

received mine early this morning, and am really happy with the product. will be fitting it in soon and will hopefully load some pictures.

Big thanks agian Ash.

Got mine today aswell.. came in the morning..

Got home from work .. lovin' life ..

trying to put it on now ..

Seems like im in the same boat as you Callan, my AFM / Pod sit way too close to the Engine.. So seems like a lil bit of chrome piping is goin' to be needed -.-

Also, on that note im going to me drilling a hole for some piping just underneath the Pod, and attatch a funnel to my bottom right of my front bar :(

Cold air intake :)

Will upload pics when im done .. probably on the weekend.

MRXTCZ

lol i think mine is just where it was mounted. I dunno will have a look but might just have to adapt the cold air box to fit cause i dunno how much more room there is in front of the pod... I need a new one anyway :P

who will be the first to put up a Tutorial with pics and what not.... that is the real question. I think ill be busy for at least a week plus i will have to fiddle with mine a bit lol

I still need to make a whole for the piping to the funnel in the front bar.. holes under neath where the pods placed..

Also need to cut holes into the box, because i got myself a blank one.

Also need to cut the box to accomodate the A/C piping and radiator overflow bottle lines.

MRXTCZ

hey good news your guys got it. dori i sent yours this arvo mate (well work did lol)

as for instruction i didnt really install one where i had to cut the holes so either wait till i do an install here in melbourne or if our good mate howie can just do a run down of how he did his with the cutting.

i have a z32 afm and didnt need to trim the afm hole so looks like theres a little difference there.

well next group buy will be with all kinks sorted out.

thanks again to all that had the patience to wait (i do get a bit lazy lol) now enjoy keeping them pods nice and cool.

received mine today ash..

looks good, fitment was tight but that's what is ideal.. bit of fiddling to make it perfect but i couldnt ask for much better

cheers

Edited by .:: GimpS-R34 ::.
vicky will call aust post and track down cause howie hasnt received his yet either so im guess delay cause of holidays or what not

but for the following ppl i hve gotten your payments and im sending the box for today

BOOSTIN96

URTWHISTLE

AZSTRYDER

R34GTFOUR

DAMOR34

VIET BOI

DORI32

GIMPS34

sheng

who pud SALISBURY down as a referance??? dont know who this is so will have to filter through my pms *sigh* please put your user name down as reference when you transfer money. who ever made the transfer can you pl;ease send me a PM with your details.

so ye again for those who are still to make payment please put your sau user name down as a reference then pm me with address.

ta

Ash

It was I that put down Salisbury as a reference.

sorry mate i did get your pm and i over looked it with so many messages just flooding through. if you still want ill send you one tomorrow morning or more then happy to refund

my apologies

now enjoy keeping them pods nice and cool.

Im planning on getting some insulation foam from clark rubber, and sticking that to the inside of the box, should be like winter for my pod then.

hey guys

can any of these ppl who has not gotten their box yet please send me a pm so ic an give you your tracking number. so far its only Sheng that has pmd me about not getting his box so i can chase this up for you.

BOOSTIN96

URTWHISTLE

AZSTRYDER

R34GTFOUR

DAMOR34

VIET BOI

DORI32

GIMPS34

sheng

also if your satisfied with the box if you can a trader rating will be great :cool:

ta

Ash

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...