Jump to content
SAU Community

Recommended Posts

I imported my 32, and as usual the aircon condensor has been removed and degassed. i think it had the old gas in it.

does anyone know if i can take it anywhere to get it regassed or do i need to find someone who has the old gas?

a place in the western suburbs would be good. thanks for the help :ninja::laugh:

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/
Share on other sites

Yeah in compliance, they will remove the gas due to some heritage law in Australia. They should re-gas it, though?

I know Profix regas air-cons! It doesn't need the 'old' gas, it just needs to be re-gassed with whatever the workshops use.

Costs about $149 from memory.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251391
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251484
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Speaking of air cons, anyone know a place that repairs dodgy air mix door/actuators? Mines short circuited and requires a replacement

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251494
Share on other sites

adelaide car care on marion road regas for less then $100 bux

i got mine done there but found out after that the air con motor had shat itself :)

couldnt find that place :D ended up taking it to isaacs auto electricians on brighton road, had to get some valves put in (as it was missing them) and regassed and serviced. works real good now tho! cold as!

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4254561
Share on other sites

Does any1 know about the sensors linked to the aircon? I've had an auto electrition look at it and they couldn't fix they said possibly sensors behind??? Any ideas????

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255017
Share on other sites

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

But i've had everything looked at the fan works but no cold air comes out??

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255031
Share on other sites

But i've had everything looked at the fan works but no cold air comes out??

ok what u need to do is run the diagnostics for the climate control... theres a guide here somehwere

basically you hold down the 'off' button of the CC unit as soon as you turn the ignition on... after 4-5 seconds it'll start up in diagnostic mode

you can then use the up and down arrows to navigate thru the options... you'll need to read the guide to interpret them, its your best bet of figuring out whats going wrong

if your fan works it could either be a compressor not working/no gas in compressor, or a stuck hot/cold mix door.... or a bunch of other stuff .... do a search on the r32 climate control and you'll find the diagnostic thread.... mine reports a shorted PBR actuator (controls the hot/cold mix coming into the car)

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255178
Share on other sites

hey mate. if it is on r12, which is the scew type service port fittings then, you need to get it retro fitted to the new gas. the old gas is no longer sold as it not ozone friendly. the reciever drier will need to be replaced as it has been exposed to the atmosphere, and the oil changed to a R134a gas type (like ester oil) it's a massive fine if anyone is caught incorrectly gas vehicles or hasn't got a licience to do so. it costs me $100 a year for my licience so i can regas vehicles. if i was you i'd get it done properly just so the a/c doesn't completely sh*t it's self and cost you a fortune. that's my 2c.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255181
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
    • The real question is, on some of those wild roads they call highways, how many times did a farmer in an old ute from the early 2000s blaze past you over double lines?   Tassie is a wild and really cool place, and after doing a work related road trip there January of 24, I understand why Targa Tasmania is ran there, and is so tough to do well at! We had a brand new Camry Hybrid that handled quite nicely, and thankfully weren't in an old car, because cresting some of those hills in a 100kmh zone for it to suddenly be like "surprise f**kers, this is a recommended 30kmh hard right turn" wouldn't be pretty. We weren't racing the Camry around, but we weren't slouching in the bends either. But my lord those old farmers know their old clapped out utes, and those roads, as they were absolutely hammering it!   You're also super lucky to make it up to Mt Wellingtong this time of year. It's often road closed with snow/ice! Also, I hope you hit up Salamander Road in Hobart for some insanely good food (I highly recommend the dimly lit Irish pub for a Guiness Pie, or even the bangers and mash!!!)   How long did the Ferry take to get across? I want to do a road trip of Tas on my own time, but I get horrifically sea sick, and I don't want me on the Ferry, just the car 😛
    • So far so good, about 30km on it so far and nothing out of sorts yet thankfully
    • Look at @Kinkstaah's thread on the issue.
×
×
  • Create New...