Jump to content
SAU Community

Recommended Posts

I imported my 32, and as usual the aircon condensor has been removed and degassed. i think it had the old gas in it.

does anyone know if i can take it anywhere to get it regassed or do i need to find someone who has the old gas?

a place in the western suburbs would be good. thanks for the help :ninja::laugh:

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/
Share on other sites

Yeah in compliance, they will remove the gas due to some heritage law in Australia. They should re-gas it, though?

I know Profix regas air-cons! It doesn't need the 'old' gas, it just needs to be re-gassed with whatever the workshops use.

Costs about $149 from memory.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251391
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251484
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Speaking of air cons, anyone know a place that repairs dodgy air mix door/actuators? Mines short circuited and requires a replacement

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251494
Share on other sites

adelaide car care on marion road regas for less then $100 bux

i got mine done there but found out after that the air con motor had shat itself :)

couldnt find that place :D ended up taking it to isaacs auto electricians on brighton road, had to get some valves put in (as it was missing them) and regassed and serviced. works real good now tho! cold as!

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4254561
Share on other sites

Does any1 know about the sensors linked to the aircon? I've had an auto electrition look at it and they couldn't fix they said possibly sensors behind??? Any ideas????

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255017
Share on other sites

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

But i've had everything looked at the fan works but no cold air comes out??

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255031
Share on other sites

But i've had everything looked at the fan works but no cold air comes out??

ok what u need to do is run the diagnostics for the climate control... theres a guide here somehwere

basically you hold down the 'off' button of the CC unit as soon as you turn the ignition on... after 4-5 seconds it'll start up in diagnostic mode

you can then use the up and down arrows to navigate thru the options... you'll need to read the guide to interpret them, its your best bet of figuring out whats going wrong

if your fan works it could either be a compressor not working/no gas in compressor, or a stuck hot/cold mix door.... or a bunch of other stuff .... do a search on the r32 climate control and you'll find the diagnostic thread.... mine reports a shorted PBR actuator (controls the hot/cold mix coming into the car)

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255178
Share on other sites

hey mate. if it is on r12, which is the scew type service port fittings then, you need to get it retro fitted to the new gas. the old gas is no longer sold as it not ozone friendly. the reciever drier will need to be replaced as it has been exposed to the atmosphere, and the oil changed to a R134a gas type (like ester oil) it's a massive fine if anyone is caught incorrectly gas vehicles or hasn't got a licience to do so. it costs me $100 a year for my licience so i can regas vehicles. if i was you i'd get it done properly just so the a/c doesn't completely sh*t it's self and cost you a fortune. that's my 2c.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255181
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...