Jump to content
SAU Community

Recommended Posts

as the topic says has any used lewis engine rebuilders to rebuild their rb26 ? their prices are very competitive. Stockish full rebuilds with forgies and acl bearings cost $5500.00 . Their "killer" engine is just under 15k which includes all top name products . Their products are also very competively priced . Check out their website - www.lewisengines.com.au.

any feedback will be greatly appreciated.

cheers

Link to comment
https://www.sau.com.au/forums/topic/244244-lewis-engine-rebuilders/
Share on other sites

as the topic says has any used lewis engine rebuilders to rebuild their rb26 ? their prices are very competitive. Stockish full rebuilds with forgies and acl bearings cost $5500.00 . Their "killer" engine is just under 15k which includes all top name products . Their products are also very competively priced . Check out their website - www.lewisengines.com.au.

any feedback will be greatly appreciated.

cheers

Remember though, thats $5500 doesnt include anything other than stock pumps and nothing in terms of head work and/or oil restriction (nothing listed on the website), no mention of decent rod bolts etc etc.

Also bear in mind if your crank comes back fked, there goes another 1k right off the bat...

So that price isnt 'the best', its fairly hefty infact when you consider they dont do anything really, but then its not the worst i guess. IMO i'd rather have a racepace motor as once you add in the extra pumps pricing, head tidy up/bolts etc etc, your well within reach of something 'upper' class as i would call it

Realistically you'd spend at least another $1500 if you wanted to make any decent power... but hey, at least they'll give you a motor with belts set right :P

So not saying anything bad about them (cause ive got NFI of their work), i just think you should shop around :)

i think his refering to dirt garage aka paul aka twoogle aka red r racing

if you dunno him start googling lol

im under the impression that paul only builds engines and you supply parts?

also how would one send an engine interstate?

Edited by R32 Driver

Paul (DirtGarage) will build it for you, PM him and have a chat about what you want. Im pretty sure he can source you parts but you will have to pay upfront for them. Best to speak to him direct about it though.

Paul built my motor (RB26) not too long ago, There is a topic on it in here somewhere. His machinist does top quality work and doesnt charge a fortune!

Airroad direct will pick up the motor on a pallet and delver it. They are pretty cheap too. www.airroaddirect.com.au

Hope this helps..

Cheers,

Johno

Not sure of your location mate but have a chat to Dan: SAU Profile | Elite Racing Website

He has extremely competitive pricing and is a stand-up guy.

I have moved a couple of engines around interstate

Sent a RB25 from Brisbane to Adelaide through NQX ~$220

Sent a RB30DET from Melbourne to Brisbane through Mainfreight ~$240 - Mainfreight were the best to deal with and you didn't need to be a business customer.

i just bought a timing belt

ill install in on the weekend any tips boys im scared

Tips for the timing belt;

Cut it in half before you install it. And then just staple it back together. Easy way to install.

Start the engine and if it doesn't seize you haven't got the timing completely wrong, you might even be close.

You don't need a timing belt anyway. mine runs fine without one, i ripped it out years ago. get with the times

Tips for the timing belt;

Cut it in half before you install it. And then just staple it back together. Easy way to install.

Start the engine and if it doesn't seize you haven't got the timing completely wrong, you might even be close.

I see no reason to turn this in to a dirt pissing contest. His ability to build an engine is well documented.

We all have our favorite spanners but if i lived in adelaide there's no way I would be getting dirt or dan to do my work, There are good builders in all major centres, Why would you risk dragging engines half way round the country when it can be done locally.

Dan from elite is my builder and i wouldnt have it any other way. But If I lived near the dirt man I would have no qualms about getting him to screw my donks together.

(If he didnt leave a note taped to the engine telling me the timing belt needed tensioning tho I would firebomb his house :( )

lewis engines has been around for yrs ive had a few speedway heads done by him . he has a good backround his dad rip john lewis owned the dyno shop at st peters on payhan rd for many yrs b4 he was killed in a plane crash . his dad did sprintcar engines and drag motors many of the top runners at the time , ive had plenty of machine work done by lewis engines with no complaints

cheers mid life crisis

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...