Jump to content
SAU Community

Recommended Posts

hi unfortunately my car got bashed my 32's driver side rear quarter panel was kicked in just wondering of any one know a rough estimate of how much it will cost im a bit tight on cash flow at the moment so i dont wanna get ripped off so if any one can help it will be awesome thanks

post-55738-1226818554_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/245046-my-car-got-bashed-r32-gtst/
Share on other sites

must hav to do with jealousy i think... also i think alot of ppl are under the impression that skylines are vry expnsiv cars or something i dont know.... jsut pisses me of to se stuff like this

i think the hammer leaves a mark like that cos the pressure is in a smaller place... if u hit a car door with something bigger say a foot or something or even ure backsidee the dent can become massive... i just hope some of these silly people get caught..highly doubt it, for now my car is getting used only wen it feels safe =[

Not sure that could be a hammer,

Cause hammers will rip / crack the paint off but its a big dent so needed some force wat ever it was!

Try DING KING they might be able to pop it out but u will need to get the car pudi / painted

thanks for all your repies unfortunately i took it to a panel beater its not just a pop out job the little groves in the quartey panel has been dented in i was told it not that easy to pop out my dent but luckly its not too bad on $$$$ and i get to touch up all my inperfections in the paint in that area but i will be shopping for the best price and a good quality job

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...