Jump to content
SAU Community

Haltech Finds The Limit Of Their R35's Engine

PJ.

By PJ.,
in General Automotive Discussion

 Share

Recommended Posts

PJ. Proficient

PJ.

Posted
Posted

As many of you may be aware the Haltech R35 GTR Skyline had a catastrophic blow up on Friday the 24th if October. Our GTR has been running on a new platform of Haltech engine management flawlessly for over 5000km's now.

The car was being track tested at Eastern Creek raceway

(http://www.eastern-creek-raceway.com/) when the engine let go. The car had completed countless flat out laps with the engine producing 400kw at the wheels, up from 300kw at the wheels - The driver tells me it was a terrific ride!

After finishing Haltech's latest Flat shifting calibrations a few more test laps had to be carried out. With no sign of trouble the car went out and successfully completed 2 more laps before finishing up on the side of the track leaving a trail of oil and plume of smoke behind it.

It was time to put it in the trailer and go back to the workshop to pull it down. After building up enough courage our in-house mechanic removed the VR38DETT from the car and set it up on the engine stand.

A few hours later the engine was fully stripped and the damage to the engine was clear - It appears Haltech have found the limits of Nissans new super car!

The engine had met its maker.

Piston #1 and #3 had separated from their lower halves right through the center of the gudgeon pin. As the Conrod's had no piston's to guide them up and down the bore they started smashing the bore, block, oil pump, sump and anything else that got in their way.

Due to the massive damage to the block we will need to replace it. And figure it's a great time to make the engine a little stronger. We will be boring the motor out and installing Darton sleeves, replacing the factory cast pistons with a study Forged unit as well as installing a set of Billet conrods. This should allow the engine to reliably produce over 400Kw at the wheels and handle the pressure.

Keep an eye on the Haltech website or drop us an email anytime for further updates.

turbo_brian Community Regular

turbo_brian

Posted
Posted

this is how the R&D works.

Drive it and upgrade it slowly until it let's go.

Once it lets go, research the causes and weaknesses, and built a package that will ultimately make the identified sections stronger, and allow much more power and upgrades to occur.

Once you have this package in, tested and showing potential you start selling the package, and perform the original process all over again.

As you get more and more performance mods, you add to stage 1's package until the engine blows up again.

Now you have the upper limit of stage 1, and the supporting aftermarket mods for it.

Once you rebuild the second motor, you have the base line for stage 2 under way, and you keep upgrading until you blow the motor again, and you again have the stage 2 kit, the supporting mods, and the upper limit all sussed out.

B.

Angus Smart Grand Master

Angus Smart

Posted
Posted

drop us all a line when you get a price on the block and other parts from nissan :D

will be interesting in the coming months whats going to happen to alot of the other cars that are pushing numbers.

good luck with it anyway and also glad to see Aussies leading the way with this kind of stuff!

:)

ras1983 Experienced

ras1983

Posted
Posted
...and also glad to see Aussies leading the way with this kind of stuff!

:)

Blowing cars up? :D

Just kidding. 400AWkW is quite astounding if the only thing changed was the ECU. So does that mean the car could have reliable and comfortably ran 350AWkW by changing just teh ecu without many dramas?

babyskyline Grand Master

babyskyline

Posted
Posted

I have been waiting for this also. Will be interesting to see if other failures result from the same thing.

Also interested to see how much all new gear will cost to strengthen it for the next round of abuse

AndrewJZX100 Mentor

AndrewJZX100

Posted
Posted

Hmm should chuck a 2J in there, 400rwkw on stock internals wouldn't be a problem then :P

j/k

like someone said, good time for some R&D and gives them a chance for a good footing in the modification of R35s.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Last Phantom
      G35 Control arm and Compression Rods into a V35 Skyline.

      By Last Phantom · Posted

      Hey crew, Failed my WOF cause of a lower control arm, and I've decided to hit both arms, and also the compression rods at the same time(seems they're gonna be the most likely upcoming failure points from some discussions with the lads over on the G35 reddit). I've looking at these form Z1:  https://www.z1motorsports.com/front-suspension/hayaku-automotive/hayaku-g35-front-compression-rod-p-40716.html https://www.z1motorsports.com/front-suspension/hayaku-automotive/hayaku-g35-front-lower-control-arm-p-40674.html I asked Z1 if they'd work as it's the same platform, just RHD vs LHD. I basically got told "Lol dunno". Specifically they aren't aware of any difference but can't guarantee fitment as they haven't done it on a 350GT. So guess I'm asking is if there is any issues with using 2005 G35 coupe suspension parts on a 2005 350GT coupe? Orginally I thought it could be something in the way of the arms that each control arm is designed to be positioned around, but that'd be an engineering nightmare for Nissan needing two different shaped control arms 😅
    • GTSBoy
      Help needed issue with heater core blower and actuator and need someone to fix this and reinstall dash - 32 - Gtst

      By GTSBoy · Posted

      ^ This. The mode door actuator is a common failure, as is the actuator and/or the actual valve for the coolant flow control valve. I also don't know how available the mode door actuator is these days. I've been meaning to look into it and get one from wherever is possible, to keep in the shed for the rainy day when mine eventually fails. Anyway, the advice to you is to search the usual NOS part supply places, or even just go to Nissan and see what they list.
    • Duncan
      Help needed issue with heater core blower and actuator and need someone to fix this and reinstall dash - 32 - Gtst

      By Duncan · Posted

      Have you got a pic of the actuator? My guess is that unit has failed internally and was flopping around, so the previous engineer who owned it forced it to be fully open to cold air (blocking the heater core path). As far as you can tell, is anything else wrong in the system? Likely you just need a new actuator (not sure how available they are) and then "installation is the reverse of disassembly"
    • Duncan
      Looking at getting a Tesla style Screen for my V37 Skyline.

      By Duncan · Posted

      I'm happy with the Lsailt unit that I put in, it puts full Android on the top screen so you can run whatever Nav and other Apps you want, while still existing inside the factory functionality like automatic reverse cams, audio input switching, retains factory bluetooth etc. Not cheap and the install was moderate (not simple, not hard) Yours is a V36 not V37 though right?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeap, all the NC's that I originally looked at that had a hard top were PRHT, which makes the roof line look horrible, hence why I said nope to them My only caveat for another MX5 was it needed to have a hard top, and initially I didn't think you could get a detachable hard top for the NC,  like my NB had Again, a big thanks to Matty for helping me source the detachable hard top for my little girl, they are as rare as hens teeth in Australia, and the few people who have them, keep them Also to Greg, for initially pointing me in the NC direction NC PRHT 🤢🤮 Not mine (I really should take more photos of my car), but a NC with the detachable hard top 😁 To me, the difference in how the detachable hard top roof line looks, and how it actually follows the bodies lines, like they do on NA's and NB's, is chalk and cheese compared to the bulbous looking PRHT  
×
×
  • Create New...