Jump to content
SAU Community

Recommended Posts

hey guys just put new split fire coil packs in my car and my mate did a compression test on my r25det s2 while he was at it

it got 150 - 150 - 150 - 150 - 100 - 150 - 150

he put oil in the bore and it went up to like 130-140 he said.

He is saying its probably the rings, but best to take it to a shop to find out.

what are my options? how much would it be for a mechanic to rip my engine apart find the problem and fix it?

budget is fairly limited, cheapest safe option here is what im looking for that will fix the problem.

any help / suggestions appreciated

Link to comment
https://www.sau.com.au/forums/topic/245868-low-compression-woes/
Share on other sites

id be checking it out definatly, its only gona get worse, all other cylinders read 150psi, and that one is 100. there should be only 10 percent variance between then in any case...

id be rebuilding it as its obviously not healthy. sorry to inform u mate...

The harder you push it, the worse it will get, you will end up with a massive blow by machine...

do a leakdown test as it could possibly be a bent valve or a head gasket problem... i think its not due to the comp bumping up with the oil test

Edited by den001

Out a little bit of oil down the spark plug hole and run the test again.

If it comes up with 150, its your rings.

Oh. hahaha.. sorry.. I should start reading threads.

Yes. Rings it is

Edited by GTS4WD

Yeah as said above, cheapest option if you don't want to rebuild it is to just buy another engine and then sell off your old one. If you can do the job yourself with mates over a weekend (it aint that hard), it will probably only end up costing you $1000 once you part of the old one.

We did it to my mates a month or so back.

where can you pick up replacement engines for that price? sounds good.. im just getting my engine tuned and gonna drive it til it doesnt wanna be driven i think -_-

i wouldnt mate, it will get so bad it will start to missfire badly, after this if u give it a good flog you risk blowing the oil up thru the breathers and leaving the sump with f**k all, it will spin a bearing and they you will be up for even more cash to fix it...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...