Jump to content
SAU Community

Recommended Posts

hey guys just put new split fire coil packs in my car and my mate did a compression test on my r25det s2 while he was at it

it got 150 - 150 - 150 - 150 - 100 - 150 - 150

he put oil in the bore and it went up to like 130-140 he said.

He is saying its probably the rings, but best to take it to a shop to find out.

what are my options? how much would it be for a mechanic to rip my engine apart find the problem and fix it?

budget is fairly limited, cheapest safe option here is what im looking for that will fix the problem.

any help / suggestions appreciated

Link to comment
https://www.sau.com.au/forums/topic/245868-low-compression-woes/
Share on other sites

id be checking it out definatly, its only gona get worse, all other cylinders read 150psi, and that one is 100. there should be only 10 percent variance between then in any case...

id be rebuilding it as its obviously not healthy. sorry to inform u mate...

The harder you push it, the worse it will get, you will end up with a massive blow by machine...

do a leakdown test as it could possibly be a bent valve or a head gasket problem... i think its not due to the comp bumping up with the oil test

Edited by den001

Out a little bit of oil down the spark plug hole and run the test again.

If it comes up with 150, its your rings.

Oh. hahaha.. sorry.. I should start reading threads.

Yes. Rings it is

Edited by GTS4WD

Yeah as said above, cheapest option if you don't want to rebuild it is to just buy another engine and then sell off your old one. If you can do the job yourself with mates over a weekend (it aint that hard), it will probably only end up costing you $1000 once you part of the old one.

We did it to my mates a month or so back.

where can you pick up replacement engines for that price? sounds good.. im just getting my engine tuned and gonna drive it til it doesnt wanna be driven i think -_-

i wouldnt mate, it will get so bad it will start to missfire badly, after this if u give it a good flog you risk blowing the oil up thru the breathers and leaving the sump with f**k all, it will spin a bearing and they you will be up for even more cash to fix it...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...