Jump to content
SAU Community

Recommended Posts

ey, it was raining and i hit the gutter and went over it.. there was no external damage however my steering became alot lighter and it wasnt straight, so basically i had to steer right to go straight.

anyone know what the problem is and how much it is to fix?

Thanks!

ey, it was raining and i hit the gutter and went over it.. there was no external damage however my steering became alot lighter and it wasnt straight, so basically i had to steer right to go straight.

anyone know what the problem is and how much it is to fix?

Thanks!

How hard did you hit it? If your lucky, it might just need a wheel alignment, however, considering that its lighter, not just veering to the left, it could be more serious, bent something etc. I'd probably take it into a Tyre shop and get them to look at it.

ey, it was raining and i hit the gutter and went over it.. there was no external damage however my steering became alot lighter and it wasnt straight, so basically i had to steer right to go straight.

anyone know what the problem is and how much it is to fix?

Thanks!

wheel alignments are cheap.....so thats if your lucky

i recall someone who driften onto the gutter...

which required changing most of the suspension.....if thats the case, make sure u start saving up

had a laugh at your title..lol.

i was driving in the wet once, lost it on a corner over corrected and hit a gutter head on. at least when i hit it i made sure the wheels were pointing straight before humping it. blew a tyre and buggered alignment. only cost me a new pair of tyres and two wheel alignments cause the first place couldnt do the job properly.

take it to a reputable tyre place and get them to check and do a wheel alignment. quite simple really. if somethings broke or bent they will tell you and you will find out how much to fix. they should not fix it without asking you firs tso you wont be surprised with a larger than average bill. I stress take it to a reputable suspension place. if you are in melb i can reccomend you one or two.

i scraped my rim to the max too LOL

i hope its the allignment then,

but its steering alot lighter, anyone know what it is? :S

Also, what about the axle? Few mates of mine say i coulda barred that,

also i buckled a rim, can i buy single ones somewhere?

I'm in melbourne,

IS beaurepairs a good place to go?

Edited by Luckieee

thought u were going to get it looked @ today hence i recommended a tire shop, cos theyre normally open 7days. if you are getting it looked @ during the week , take it to a suspension place that does alignments. where u from?

Like i said if something were to be bent its probably a lower control arm, or steering rack. Hope your rack hasnt snapped?? could explain the light steering. if so i wouldnt be driving.

Just have a look under the front car and inspect

where can i get cheap alignment done? :D

i guess you'r not heeding my adivce to go to a proper suspension place hey?

Traction tyres rowville is where i take my car to or you can try Centreline if your on the other side of town. The guys at Traction tyres are a class act and will tell you what needs to be done to fix things and nothing more. $66-$77 for front and back from memory. Should be cheaper for just a front end alignment.

g/luck with it.

so they got they told u that your control arm is damaged and charged for a wheel alignment!! if your control arm is bent, they wouldn't be able to align your car properly. i would take it elsewhere, ie try the ones recommended by the guys above. and if its confirmed that your contorl arm is bent get it fixed and demand a refund for the dodgy work done @ beaurepairs. if u have any issues call the dept of fair trading or the beaurepairs head office.

if you need a control arm, check out some of the wrecks in the for sale section. or call some local import wreckers.

;) they could have charged you just a small fee to look at your car and see if theres a problem and then go from there but then again your steering was pretty out of wack wasnt it I got TTyres to do to double check the dodgy alignment i got previously before i went ahead with anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...