Jump to content
SAU Community

Recommended Posts

hey this is my first entrance... (topic)

I kno its SKYLINES only but i wanna get a supra and i ve been reading up about importing it and I ve been browising these forums for quite some time now..

but i found a dead cheap supra on ebay and i just wanna knnow if it is worth gettting it..

thats the item description...

" You are bidding on a REPAIRABLE WRITE OFF SUPRA 1995. I'll try and be as accurate as possible but if you have any queries just email me.

I bought this car as a write off from fowles auctions Melbourne over 2 years ago and never got around to finishing it for reasons i will state below, its just sitting in my yard and I have no intention of finishing it. I have spent over 16,000 on it thus far.

It was repaired by Performance Crash Repairs in Adelaide with receipts. It was very hard to find the parts for this car and the repairer took his sweet time to getting around to it, but in the end it was a pretty good job and the panels align dead straight.

After getting it back from the repairer i found the car would not start due to an electrical problem. I replaced a lot of the key electrical components but still nothing..

I took it to an auto electrician which found out it was a dry solder joint in the instrument cluster. And 400 bucks later it starts without a problem.

As i was putting the rest of the little bits and pieces back together I found that the brake master no longer works, and possibly the clutch master. So after almost 2 years I just had enough with it.

So now to the good and bad and what needs to be done:

GOOD:

Starts, good compression in all cylinders

only 125,000 km on it roughly I believe as this was the date on the service sticker on the windshield when i got the car. Though the current cluster shows 150,000 but this is a replacement cluster as the original was stolen during transport to Adelaide.

Panels all straight and freshly resprayed 2 years ago.

Has receipts for parts and repairs including vin numbers etc..

Car is complied.

its the 95 model with the larger brakes etc..

can be registered still.

BAD:

Needs a windshield, bonnet release cable, airbox enclosure.

It starts ok but when it warms up the car will chug and stall, I believe this is due to the missing air temp sensor on the airbox enclsure which i dont have.

interior could do with a bit of a clean.

comes with 3 mags and a space saver as the 4th mag was damaged when i got it.

Have a look at the pics or come have a look at the car if you are interested, I don't have a battery in it at the moment but i will try and get one by sunday so i can start it up if anyone is interested.

Would make a cheap daily just finish off the bits and pieces and get it registered or a cheap track car, just drop in a 2JZ-GTE.

One of the pics shows it is missing a side skirt but i have it just havent put it on the car.

I just dont have the patience for this anymore, everytime i fixed something I found another problem, as a result i cant be bothered to look for a brake master and airbox, bonnet cable... this car has cost me too much and just want to cut my losses and start over. I will update then when i think of more things.

"

direct quote of the descrpition

now is it worth it.. paying 3 grand(bargainign it down) and then investing another 5-6g to get it working?

SORRY IF IM OFF TOPIC HERE ITS MY 1ST TIME

thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/246205-toyota-supra/
Share on other sites

ey

thanks guys

yeah i slept on it.. i dont think its worh it could be a major lemon if its that cheap

u know, somepeple like to buy things in shambles and work on things themselves...somepeople find it a hobby to work on their cars.

but if your hoping to buy a cheap as chips car thats broken and fix it.,..then drive it hoping nothing is going to go wrong. then this car msy noy be for you.

check out trading post, theres some dirt cheap supras.

look, buying an import or any second hand car, theres always a risk. unless the car is brand new.

Link to comment
https://www.sau.com.au/forums/topic/246205-toyota-supra/#findComment-4282822
Share on other sites

Personally, I wouldn't touch it, as it certainly sounds like it's stuffed. Yes, some people like to get things working themselves but with something like that, you have no idea how much it's going to cost to actually have it running and be reliable.

Besides that, the non-turbos Supras aren't really that fast. You want go to match the show, right? Unless you're on your P's... :)

If you *really* must have a Supra and can't get a turbo, then I guess that would be a better choice than a non-turbo (say R33) Skyline. You've got the extra 0.5L capacity and I really think that makes a big difference, and generally the consensus is that the Supra looks better than the R33 Skyline.

Practicality wise - have you thought about this? The Supra has no useable boot/hatch to speak of - it's basically about half a foot deep and if you want a sound system, that's most of that space gone. The Skyline's boot is much more useable. Same with the back seats - forget about more than 2 people in the Supra - but 4 or even 5 will fit in an R33 quite comfortably.

Finally, if you look around the private import mobs like prestigemotorsport.com.au, j-spec.com.au and one that Terry above recommended to me: www.topsecretimports.com.au - you will find something in your price range, or maybe *slightly* more, that should be in pretty good, and most importantly, a *running* condition!

Hope that helps!

Link to comment
https://www.sau.com.au/forums/topic/246205-toyota-supra/#findComment-4294545
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...