Jump to content
SAU Community

Recommended Posts

nope. new rules say its within so many mm of standard rolling diameter.

however, youre still only permitted a 1 inch increase in track per axle (about 12.5mm per side).

as most know, defected at the ns cruise for the following;

legit;

1) suspension too low. (its sacked, simple, i know it, you know it, they know it, not complaining)

2) tint too dark. (true, its 35% when it should be 70%, but realistically, as soon as i put my sunnies on, im driving illegally anyway)

retarded/not so legit;

1) boost gauge not permitted. (no reason given, not mounted on crash pad, not obscuring speedo/tacho, nothing was said about water temp gauge on the steering column).

2) wheels have extra holes, not suited. (multifit rears, as purchased, apparently illegal for reasons that i couldnt comprehend)

3) wheel nuts to be replaced with standard. (im using anodized red steel wheel nuts, these are apparently not legal because theyre less likely to bend or break compared to standard wheel nuts... i shit you not).

i was also warned that my adr approved velo bucket seat was unsafe because the cushions are removable and might come off at any given time while driving, its been in for 2 trackdays and has stayed exactly where i put it, complete bs.

i expect the last 4 entries to be laughed at when i get to regency.

Edited by scandyflick
as most know, defected at the ns cruise for the following;

legit;

1) suspension too low. (its sacked, simple, i know it, you know it, they know it, not complaining)

2) tint too dark. (true, its 35% when it should be 70%, but realistically, as soon as i put my sunnies on, im driving illegally anyway)

retarded/not so legit;

1) boost gauge not permitted. (no reason given, not mounted on crash pad, not obscuring speedo/tacho, nothing was said about water temp gauge on the steering column).

2) wheels have extra holes, not suited. (multifit rears, as purchased, apparently illegal for reasons that i couldnt comprehend)

3) wheel nuts to be replaced with standard. (im using anodized red steel wheel nuts, these are apparently not legal because theyre less likely to bend or break compared to standard wheel nuts... i shit you not).

i was also warned that my adr approved velo bucket seat was unsafe because the cushions are removable and might come off at any given time while driving, its been in for 2 trackdays and has stayed exactly where i put it, complete bs.

i expect the las4 entries to be laughed at when i get to regency.

most likely. and this is the truly sad thing when it comes to rookie cops/non traffic cops that havent got a clue but want to make a quota.. any chance the first two could have been classified as a minor defect and get cleared at sturt or some other police station?

I still cringe when I hear of idiot cops trying to defect turbo cars simply because theyre running a stock BOV..

-D

well, ive got the paperwork in front of me, defect category is marked as minor. but apparently, being suspension related, that requires a full regency inspection. aids. but im gonna try for a copshop clearance anyway.

well, ive got the paperwork in front of me, defect category is marked as minor. but apparently, being suspension related, that requires a full regency inspection. aids. but im gonna try for a copshop clearance anyway.

bollocks. if its minor it can be cleared by a cop shop

minor = detectable and verifiable by a cop shop inspection

major = cops arent sure and want regency to make sure

-D

Edit - Gauges are all legal provided they a) dont obstruct vision, b) are securely attached c) are not in the travel path of your skull if your car was to go from 60-0 in 1 metre.. multifit wheels sold in Aus are always legal, otherwise u can sue the tits off the seller and manufacturer - if theyre JDM you could be shit out of luck, re wheel nuts - not sure why but they tend to want stock wheel nuts and tyre air valve plugs with stockers, rather than ADR/CAMS approved variants - again, I think this is due to stupid politicians with nothing better to do, but there it is... gotta chuck the stockers back on for now it seems.. last one sounds like the argument of a man who knows he using and wants to make a cheap shot - if its ADR approved, fitted on an ADR rail then I see no problem.

Make sure you document absolutely everything, matter of fact it'd be good if you recorded your conversations while they're going over the car so we can analyze it.

-D

bollocks. if its minor it can be cleared by a cop shop

minor = detectable and verifiable by a cop shop inspection

major = cops arent sure and want regency to make sure

-D

Not when it's ticked for a Vehicle Inspection Station and not a cop shop; but I'd still try my luck anyway

<snip>

yup, thats basically my way of thinking. the seat will probably be a no no at the end of the day though, while the rail is super solid (you yank on the seat and the car moves with it), it isnt an adr rail. and also being a 2 door car, im not dead certain, but im 90% sure that you cant legally rock a fixed back unless you basically remove the back seat and register it as a 2 seater.

wheel nuts im not changing. his reasons were bullshit. and in the book tyrepower has about all this shit, wheels nuts are only mentioned in regards to the minimum number required per wheel, 3.

the gauges ill be removing, but ill be quizzing the traffic guys at the local cop shop about placement when i swing past with the 200.

Not when it's ticked for a Vehicle Inspection Station and not a cop shop; but I'd still try my luck anyway

oh, i will be.

and if i have no luck there, im going to see if terry (troys dad) can take it through regency for me, im thinking they'll be kinder to an old mate doing someone a favour than they will be to me.

most likely. and this is the truly sad thing when it comes to rookie cops/non traffic cops that havent got a clue but want to make a quota.. any chance the first two could have been classified as a minor defect and get cleared at sturt or some other police station?

I still cringe when I hear of idiot cops trying to defect turbo cars simply because theyre running a stock BOV..

-D

My Ceffy got done for having a stock blow off valve, and so did my mates 32. Shame there is nothing we can do about it. :D

Sucks the most was I was minding my own business down the road when an undercover copper appeared outta nowhere cutting off 4 other drivers behind me.

My mate was in a carpark waiting for some friends, parked near him told him to pop the bonnet. Shit is just ridiculous. :(

hey guys, is a oil cooler a defect and/or would it pass regency? if not what about a sandwich plate inbetween the oil filter to plug gauges into? is that a defect?

no on both counts, provided its done righht

-D

properly mounted dude. and not leaking. ill be hella surprised if my kit isnt passed.

and i doubt you need braided lines for it to pass, as long as the lines and fittings are designed for the job (not leaking), it shouldnt be problem.

im using earls billet blocks with an earls core, earls high temp & high pressure rubber lines with speedflow fittings throughout.

Edited by scandyflick
being a 2 door car, im not dead certain, but im 90% sure that you cant legally rock a fixed back unless you basically remove the back seat and register it as a 2 seater.

i called vehicle standards about this and was told that aslong as one of the seats comes forward to allow entry to the rear seats then there is no drama, even said if you put it in writing to them they will give you that in writing.

as most know, defected at the ns cruise for the following;

legit;

1) suspension too low. (its sacked, simple, i know it, you know it, they know it, not complaining)

2) tint too dark. (true, its 35% when it should be 70%, but realistically, as soon as i put my sunnies on, im driving illegally anyway)

retarded/not so legit;

1) boost gauge not permitted. (no reason given, not mounted on crash pad, not obscuring speedo/tacho, nothing was said about water temp gauge on the steering column).

2) wheels have extra holes, not suited. (multifit rears, as purchased, apparently illegal for reasons that i couldnt comprehend)

3) wheel nuts to be replaced with standard. (im using anodized red steel wheel nuts, these are apparently not legal because theyre less likely to bend or break compared to standard wheel nuts... i shit you not).

i was also warned that my adr approved velo bucket seat was unsafe because the cushions are removable and might come off at any given time while driving, its been in for 2 trackdays and has stayed exactly where i put it, complete bs.

i expect the last 4 entries to be laughed at when i get to regency.

i lol'd so hard at those retarded 4 points.....wtf is with the wheel nuts, i cannot use standard wheel nuts on my wheels as they wont even come close to fitting.....i am getting more and more worried about these wanna be uneducated cops trying to issue a defect because in their eyes we are all hoons and should be off the road.....

as far as i was aware in regards to the bucket seat, you wont be able to have a fixed back in a 2 door car registered as 4 seater.....you would have to ditch the rear seats plug all the holes and crap and then reregister it as a 2 door 2 seater car and that way you can have both front seats as fixed back......well this is what i was told when i last when through regency

for anyone thats interested, i just printed something off dtei that says as of the 1st of jan, 35% tint will be legal on windows except the windscreen (obviously).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...