Jump to content
SAU Community

Help!!! my Rear Number plate does not fit

R31Heaven

By R31Heaven,
in General Automotive Discussion

 Share

Recommended Posts

R31Heaven Proficient

R31Heaven

Posted
Posted

Got my car registered today and the Back plate will not fit, about 10mm either side to big. I own a R31 GTS-X. Questions are:

1. can you modify the standard plate to make it fit?

2. Can you get a Sticker/sign writter to make one up with a reflective background.

is it legal to do the above any off the above if not what the hell do you do???:P

R31Heaven Proficient

R31Heaven

Posted
  • Author
Posted

The only way I can see I am going to get it to fit without getting in the way off the number plate lights it to cut it in half and slide one half over the top of the other making the letters & numbers closer to each other...... Yep they are slimlines

R31Heaven Proficient

R31Heaven

Posted
  • Author
Posted

Ok I have attacked my plate as recomended by Vic Roads & others on here. I rang them this afternoon about this, and there words were bend cut bits off as long as it is afixed to the car. So out came the tin snips and some trimming & bending has accoured...:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...