Jump to content
SAU Community

Clutch Slip In 3rd Under Full Load

DMAN#20
 Share

Recommended Posts

DMAN#20 Explorer

DMAN#20

Posted
Posted

hey guys i have had this only happen once yesterday, the clutch is a exedy five button and has only 2000kms on it with only a few hard launches. its in an r32 gtr with 265kwatw. my question is this common or does it need some sort of adjustment?

something else to mension i wasnt driving around for long when i gave it some stick!

Link to comment
https://www.sau.com.au/forums/topic/250009-clutch-slip-in-3rd-under-full-load/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted (edited)

hmmm

your rear main seal has begun to leak and some oil got on your clutch maybe?

or your clutch may have just had some clutch dust or something on it from over use?

Edited by Boostin96
89CAL Grand Master

89CAL

Posted
Posted

well as long as the engine is putting out less power then what the clutch is designed for (or a similar amount of power even) then it shouldnt just slip for no reason. maybe it just needs to bed in if its only just been installed but if it was done with the engine then im not sure it shouldnt be slipping

is it doing it all the time?

Beer Baron Grand Master

Beer Baron

Posted
Posted

well whatever it is get it sorted asap. slipping clutch will only get worse. and if it's just a simple set-up thing allowing it to slip will just wear the clutch out quick smart. I would say it's set-up/install problem. possibly wrong length sleeve/bearing carrier used, or the take up point incorrectly set-up so that the clutch is not completely engaging etc. the other thing is it could be a faulty pressure plate, or even just a clutch not up to the job. but i'm still banking on set-up/install since it's so new.

DMAN#20 Explorer

DMAN#20

Posted
  • Author
Posted

brand new lightened flywheel!

it had previously a hyper twin plate which was undriveable, the take up point was very short, this clutch had only 1000kms on it, so i sold it and got the button type

No Crust Racing Grand Master

No Crust Racing

Posted
Posted

Pressure plate is certainly a possibility if it was not replaced. They fatigue over time and if you have a new clutch the clamping pressure will be higher which is more strain on your pressure plate. The 6-spd tremec in the VY SS I sold a while back had this issue.

Take it back to where you had it installed, get them to sort it. Quick smart like Baron said, slip = wear.

  • 4 weeks later...
DMAN#20 Explorer

DMAN#20

Posted
  • Author
Posted

OK heres the low down, spoke to exedy mel. today and they said that the sports tuff heavy duty button clutch that i have will only support 400 - 450hp at flywheel, seeing as i have 360hp at all wheels they say that it is border line and that i should go for a hyper twin plate setup. Ive already had one of these and it was undriveable! Any suggestions???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...