Jump to content
SAU Community

Recommended Posts

Originally posted by GILTY

I have a badge on the back of my 32 GTS-t that is often mistaken as a GTR badge...have a look see and tell me what you think???

yeah ive seen that on a few cars , may i ask where you got it a freind is after one ?

Link to comment
https://www.sau.com.au/forums/topic/25051-fake-gtrs/page/3/#findComment-533588
Share on other sites

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

stereotypes come about due to the masses of the targeted group being in such a manner as to leave a lasting impression on the public/peers.

Hence p platers are hoons/bad drivers, due to most being inexperianced in shoddy cars and trying to drive beyond their abilities.

old people are percieved as being doddering old fools who drive slow complain about everything and are mortal enemies of the youth. Mainly because the majority or atleast the most vocal do these above things.

same with p platers and skylines, they rice them up, they cant afford a gt-r but a badge/front bar is a fraction of the cost etc. Hence the stereotype :)

Link to comment
https://www.sau.com.au/forums/topic/25051-fake-gtrs/page/3/#findComment-534863
Share on other sites

Fark...notin more i hate den people tryin to make a car into something it isnt. A GTR badge on a GTS-T is already bad enough, but i really really cannot stand lancers tryin to be EvO's. LIke seriously man!! Lancers are a piece of sh*t....farkkk.......seriously man...the body kit for a GTR is nice..but a badge? mannn wannabe cars like the evo etc....jus get laughed at by people who know something about cars.

i would seriously be embarassed driving around in a fake Evo wannabe or a GT-R wannabe. I would rather be drivin around in a nice stock GTS-T skyline or a Stock lancer. At least im not tryin to be somethin im not. =)

Link to comment
https://www.sau.com.au/forums/topic/25051-fake-gtrs/page/3/#findComment-535879
Share on other sites

well i agree with most ppl here...

a body kit's fine

but GTR badges are a no no...IMO you look like a tool, and deserve to be laughed at lots :)

and talking of badges......i saw a 180 yesterday, with just the red "R" bit from a GT-R badge on the back of it :confused: WTF?

Link to comment
https://www.sau.com.au/forums/topic/25051-fake-gtrs/page/3/#findComment-535898
Share on other sites

If everyone is comfortable with thrwoing opinions around, and as this thread is prefixed by a poll, here's mine.

I reckon gts-t's *can* look great with a gtr kit. I have seen some that are a bit on the cheap side but what you must remember is that it is up to each individual's personal taste - not yours.

I have to tell the orignator of this thread that there are about 6 different reasons to flame/spam/sign-u-up-2-pr0n-lists in your first post. You appear to be close minded, un-intelligent and arrogant beyond your probable 16 years. I'll leave it there because I could tear your post apart but my lunch just arrived...

To everyone else that has posted, thanks for your valuable (mostly) opinions and contribtions. That's what makes this forum so great. To all the people that are down on others for the sake of it, get a chainsaw up your collectives!

Adrian

Link to comment
https://www.sau.com.au/forums/topic/25051-fake-gtrs/page/3/#findComment-536476
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...