Jump to content
SAU Community

Recommended Posts

just some parts that i have left from the wreck

just want to get rid of em

both side mirrors 80

both doors 100

all windows apart from windscreen '

gtr rear spoiler 100

bootlid 60

rear pods 110 not budging on these or else ill keep em

rear bar 60

lhf seat 70

a pillar trims with 3 screw holes for tweeters 50

rhf main power window switch 60

both front clear indicators (clear with abit of orange) 60

lhf headlight with bottom thread stud broken (the one that no ever cbf putting back on) 50

4 kybshocks with king springs front and rear 100

1 rhf type m side skirt 40

front hubs lhf+rhf 150 goood for 5 stud conversion

might have some other stuff which ill put up along the way if i can think of em

cheers

all parts located in melbourne springvale

contact through pm or if u want a quicker reply might as well call or sms 0412-219-552

Link to comment
https://www.sau.com.au/forums/topic/250925-r32-gtst-parts/
Share on other sites

im after the demister airvent, the one on the very top of the dash. Let us know if you have one which isnt warped by the sun.

Cheers

lol

sorry keeping these, cause mine have gone and broken into different pieces

Link to comment
https://www.sau.com.au/forums/topic/250925-r32-gtst-parts/#findComment-4345657
Share on other sites

its me thats picking them up on monday, at least i hope, i msged ya the other night asking if all the clips are intact and you said you would check monday, let me know mate

Edited by HI2U
Link to comment
https://www.sau.com.au/forums/topic/250925-r32-gtst-parts/#findComment-4347317
Share on other sites

possible to get a small cut from the LH rear corner of the boot shut area, not bootlid just the corner, where there is the radius of the boot, rear guard & beaver panel. only need a section about 300mm x 300mm, but you may have to cut the guard or unpick,

is courier pickup an option if i shoot funds over the wire??

let me know cheers nathan

Link to comment
https://www.sau.com.au/forums/topic/250925-r32-gtst-parts/#findComment-4347874
Share on other sites

guys if u are interested.

i wanna get rid of the shell, just the shell only so the rear gaurds roof and that are still good just not the front .

if someone wants 100bucks ono pickup

i just want it out my drivway cause its taking up space.

cheers

Link to comment
https://www.sau.com.au/forums/topic/250925-r32-gtst-parts/#findComment-4348196
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...