Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

i have a t67 i believe with a 8cm exhaust housing and have not been able to find a larger one to suit, you people with td06's do you know the exhast wheel size to compare, mine it 60mm from memory. Im not sure what to do atm as it will spool up nice and early with very little lag but not sure how much it will kill the top end.

Im not sure if the T67 uses the TD06H or the TD06 turbine, or another again. I have often read/seen ppl refer to the TD06-25G as the same turbo as the T67-25G, but there could easily be subtle differences, hence the different designation

What size are you after Clint as i have a 10cm and come the end of the week will know whether i want to go smaller, so may be able to trial fit one anothers and see how they go. I may even like to try the 8cm to see if i make the same top end power but with better response...perhaps telling me that my head, valves (???? i duuno) are more of a restriction then the exhaust housing on an RB20.

i would like a 12cm but a 10 would be ok too, thats why i need to find out if the TD06 has the same exh wheel, the blokes at MTQ said it was bigger than a TD06 and they couldnt find anything suitable in the misubishi range.

My engine is being done on a engine dyno so i dont wont to change it once fitted, so if i cant find something suitable i will just use it, can always add some extra power with Nos for the strip.

i think the 8cm is just another way of saying ar.. type thing.. just find out what a 8cm, 10cm, 12cm is equal to and there is your answer.. 8cm mite be .6 or something??? have a look at the ihi rx6 turbo.. very small exhaust housing but huge comp cover.. spools up at like 2800-3200 on sr20 but still packs enough for 300rwkw+ mite the same deal with your t67 with 8cm housing..

Dotn Apexi use a different convention again?

They typically have a P in front of their housing size referecne, which i think is the A/R in mm^2/mm, where as Garret use in^2/in so a Garret 0.87 equates to about the Apexi P22.

So how that helps me work out the Trust 8, 10, 12, 16 cm^2 housings i dont know ...anybody?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...