Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Guys I've had a closer look at the neo head now and I've gone with the external oil feed solution. I was about to try drilling through from the oil gallery for the lifter but decided against it because I reckon that the VCT will be calibrated for operation on nominal pump pressure from the block. I'm just not 100% sure that there won't be some pressure loss down that gallery feeding the lifters with all the points of loss at each lifter and don't want the VCT doing strange things.

I just think there must be a reason that the nissan engineers decided to run a standalone oil supply to this rather than using the existing head supply.

  • Like 1

It's not that surprising at all since it's a pressure actuated mechanism. The oil supply to the lifters is seriously restricted already (see oil control stuff) then is opened out into a ~15mm gallery that feeds oil to all the lifters. It may work OK on the R33 on/off VCT but I reckon it's unlikely to work perfectly on the Neo head with the variable degrees of advance/retard.

It's not that surprising at all since it's a pressure actuated mechanism. The oil supply to the lifters is seriously restricted already (see oil control stuff) then is opened out into a ~15mm gallery that feeds oil to all the lifters. It may work OK on the R33 on/off VCT but I reckon it's unlikely to work perfectly on the Neo head with the variable degrees of advance/retard.

The neo vct is either on or off, no variable.

The neo vct is either on or off, no variable.

I see...so what is the function of the oil? I'm not game to pull the gear apart in case it's full of complex little bits? I assume it's always in the nominal position for high revs and in the low revs is releases oil to the mechanism that rotates the gear relative to the camshaft. If you didn't have an oil mains pressure supply could it half actuate or not actuate at all?

the solenoid actually stops the oil AFTER the gear. What this does is pressurises it and pushes it / makes it rotate inside.

Thanks my understanding anyway.

When the solenoid opens, it releases the pressure and a spring returns the cam to the normal position.

Please correct me if I am wrong.

It indeed does need pressure.

the solenoid actually stops the oil AFTER the gear. What this does is pressurises it and pushes it / makes it rotate inside.

Thanks my understanding anyway.

When the solenoid opens, it releases the pressure and a spring returns the cam to the normal position.

Please correct me if I am wrong.

It indeed does need pressure.

Pretty sure this is wrong. The oil supply quite clearly comes up through the head from the block, passed the solenoid (depending on its state) then to the cam.

33 and 34 vct activation is different.

On 33 heads, the oil constantly feeds the front journal to lubricate it. The oil leaves the journal via the vct solenoid into the head. When the vct engages the solenoid blocks the drain which pressurises the pulley and advances the cam. The semi constant oil drain from the front journal is the reason for the oil drain in the front of the 33 vct heads.

If you look at the head and the cam you can see the oil holes are in line and it lines up with the groove in the cam which is ported to the cam pulley

On the 34 neo head, the front journal lubrication comes from the same main gallery as the rest of the cam bearings.

The vvt solenoid has its own feed which is closed when the vvt is off. when it turns on, it feeds pressure to the grove in the cam which activates the vvt pulley. When it turns off, it shuts the oil feed from the block, and vents the oil pressure in the pulley to the head.

If you look at the front cam journal you will see the same 2 holes as the 33 head, except they are not in line, and the grove in the neo cam lines up with the oil hole from the solenoid only.

The advantages of the 34 system are the cam journal is always fed with pressurised oil like the rest of the journals, and the vvt only discharges a small amount of oil into the head when the vvt switches off, instead of the constant loss of the 33 system.

This also explains why a few people here and there who just block off the vvt on their 33 head and run an rb20det or similar cam, seize the cam as there is no dedicated lubrication to the front journal.

sorry no photos on hand to show what i mean, and couldnt find them on google

  • Like 2

Good call, I've ended up with the head that the internal mod was done on (mustn't of been used until I got it). But it didn't work, seems like not enough pressure to engage the vct, so I just got rid of it completely

I've been thinking a little more about this; how would you know that it wasn't working? Your ecu could be actuating the solenoid but if your oil pressure is insufficient to actuate the cam then I don't know how you'd know? Unless you had previous seat of the pants experience with the motor or another car with similar specs to compare against? It's not like a light comes on in the dash when camshaft is advanced?

Because I did numerous tests on the solenoid, also hooked it up so it would come on with a switch to test at idle, note of engine didn't change at all. Did numerous dyno runs with it on/off and different rpm switch points, no difference.

even pulled the bolt that lets the oil through to vct gear out and replaced with a Solid bolt still no difference.

I don't think it was working.

Could be wrong

Because I did numerous tests on the solenoid, also hooked it up so it would come on with a switch to test at idle, note of engine didn't change at all. Did numerous dyno runs with it on/off and different rpm switch points, no difference.

even pulled the bolt that lets the oil through to vct gear out and replaced with a Solid bolt still no difference.

I don't think it was working.

Could be wrong

Must of been another issue. I have done the internal mod and been working fine for 1 year. Full vct function through boost street
  • 5 months later...

hey guys sorry to bring this back up but as im building one i thought i might ask ive attached a picture with my head and was looking at the core plug #1 and was wondering on the other side of it if i was to drill it to provide oil to vct off the main bucket gallery's

also i couldnt work out how to add the pix sorry

Edited by devilsknife
  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...