Jump to content
SAU Community

Recommended Posts

hey guys, how much is it to replace a windscreen roughly (r32)? is it worth buying a used one and getting it swapped?

Couple of neighborhood kids thought it would be a good idea to chuck rocks at my house (got 2 smashed house windows and my windscreen damaged and house mates Lexus has a few dents in it). They threw rocks for around 15 minutes, couldn't really see where they were coming from as it was too dangerous to go outside. Cops showed up after 20 minutes but i guess they ran off after that. Has to be one of the houses behind our street .. cant wait to figure out who it was :angry:

Oh and also, if someone has a house for rent in south east anywhere ... ill take it. I've had enough of this northern suburb BS.

Link to comment
https://www.sau.com.au/forums/topic/253074-r32-windscreen-cost/
Share on other sites

thats where you go to your gun shed, pull out the bean bag shot gun and start shooting back!

bloody little kids, if you have a younger person you know who goes to the local school , better set him up with some cash to fish them out.

hey guys, how much is it to replace a windscreen roughly (r32)? is it worth buying a used one and getting it swapped?

Give National Windscreens a call. It was 3 years ago, but a brand new one was $180 fitted on site for my GTR. I wouldn't bother with a second hand one, personally.

As to the radio not working, R32's (well, GTR's at least) use a 'diversity' system which uses an antenna built into the front windscreen AND the rear windscreen de-mister grid as an antenna (there's a module in the LHR quarter behind the boot trim that has antenna and grid power connections, it acts as some sort of filter system to eliminate radio interference). Of course this assumes your still using the stock radio (unlikely.....). I disonnected the rear grid antenna connection and added one of those aftermarket Aerpro hidden antenna's. Works fine.

Give National Windscreens a call. It was 3 years ago, but a brand new one was $180 fitted on site for my GTR. I wouldn't bother with a second hand one, personally.

As to the radio not working, R32's (well, GTR's at least) use a 'diversity' system which uses an antenna built into the front windscreen AND the rear windscreen de-mister grid as an antenna (there's a module in the LHR quarter behind the boot trim that has antenna and grid power connections, it acts as some sort of filter system to eliminate radio interference). Of course this assumes your still using the stock radio (unlikely.....). I disonnected the rear grid antenna connection and added one of those aftermarket Aerpro hidden antenna's. Works fine.

how s the reception?

damn man. i hate little kids...

kids started throwing plums at my house at night. but.. we hid and we lay in wait. for which we pelted their homo asses with water balloons and hosed the little mofos down till they started crying.

ambushing.... its teh shizzz

they did a farking shit job of it but meh what can you do

The important thing when having a windscreen replaced - and it doesn't matter who does it - is to make sure any damage to the paint under the old sealer is repaired BEFORE putting the new windscreen in. When they remove the old sealer they always scrape the old sealer off and can damage the paint, which could expose the underlying metal resulting in corrosion down the track (the new sealant only delays the inevitable). I've seen this on many cars and had to do the repairs, which in extreme cases involves lots of welding.

I usually use a high zinc primer or something like Kill Rust, but I also ask the installer to come back in a few days after he's removed the windscreen. That give me time to restore the paint, they usually don't mind, but I realise that might be difficult if you need the car back on the road quickly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...