Jump to content
SAU Community

Recommended Posts

Mate, I'm runnin in my R32 Gtst 14psi, dyno'd at 165.6rwkw/457Nm @ 6500rpm tuned on a 28deg day by Dr Drift and only managed a 14.452 at 98.7mph.

I have a full 3" turbo back, hi flow cat, intercooler, pod, bigger fuel pump & boost controller for the life of me couldn't break the 100mph mark no matter how many times I tried(did 15 runs)

My best re-action time was .440.

There's a big difference of what a 20yr old car can do compared to a fresh outa the factory car sprouting figures on paper is meant to do.

Mine before remapping was puttin out 116rwkw with all the mods I have listed and was running lean as up top before remap.

The only way you will know is to get it on the strip & see for yourself- if your up in Qld your welcome to come to our next Drag day & see how you go-we would love to see you there-Qld Events team out :D

perth but thanks for the friendly invite :P gunna try get a helmet off a mate and go to kwinana this coming wednesday. will post the results.

  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

turbo back exhaust

Profec B 1bar (a little more boost than is good for the turbo just for the drags)

Bosch 044 in tank fuel pump

remapped ecu

9 puck clutch

Cold air partitioned air filter (metal pipe turbo intake)

Full suspension kit setup with pineapples, revalved Tien's and camber /castor setup for traction

Decent width 245 rear tyres with some air let out.

turbo back exhaust

Profec B 1bar (a little more boost than is good for the turbo just for the drags)

Bosch 044 in tank fuel pump

remapped ecu

9 puck clutch

Cold air partitioned air filter (metal pipe turbo intake)

Full suspension kit setup with pineapples, revalved Tien's and camber /castor setup for traction

Decent width 245 rear tyres with some air let out.

nice, hmmm well im on my way to that :)

already got 3" metal intake(best induction noise ever :)), full zorst, brass button clutch. needa partition my intake though for cold air. gunna get injectors and pump soon with an ECU remap. Got pineapples set up for rear squat atm and i have ALL of the front and rear bushes, adjustable where available sitting in my room waiting for swaybars to arrive before i install them. tyres are 255's but shitty ones, i dont think ill put more than 13 psi through the turbs though. wait till i get a 25 turbo.

I been told 25 PSI in the tyres while I'm at drags. That about right ?

cbf drag radials. I'm either gunna get some adrenalins or potenzas soon though. Should be better than the cheap crap on there now

trial and error with the tyre pressure.

too low and you will have less contact patch on street tyres and potentially lower the grip levels.

start with 30psi hot pressure and drop a few psi at a time if you think this is a problem.

drop it down to 16ish psi

the rims wont spin inside the tyres or any of that rubbish

If you're running 40psi in your tyres with the 1/4mile runs, thats half your problem. Also with the launch, dont dump the clutch, hold the revs up and "feather" it out and jump on the throttle at the same time. You should get 2.0 or even 1.9 with a good launch

  • 3 months later...

For anyone who is interested i got down to the drags the other day and this is the results, if you havnt read whole thread i was testing against an iPhone app.

also again, car is stock motor/turb o, just a pod, 3inc turbo back with stock cat and a FMIC.

first test run:

Actual data from motorplex:

ET: 14.73 @ 158.98kmph

60': 2.54

330': 6.46

660':9.68

1000':12.43

iPhone app data:

ET: 14.75 @ 157.9kmph

60': 2.36

330': 6.34

660':9.60

1000': 12.4

second test run:

Actual data from motorplex:

ET: 14.89 @ 159.32kmph

60': 2.71

330': 6.65

660': 9.83

1000':12.59

iPhone app data:

ET: 15.28 @ 152.9kmph

60': 2.72

330': 6.79

660': 10.06

1000': 12.91

my best run for the night was a 14.45 @99.33 mph, wasnt a good launch or change into 4th either, so i know it can go faster

I went to the drags in my 32 for the first time and ran a best time of 13.761.

Trap speed was 104 mph.

Running an RB20 dynoed at 197kw atw, on 255 adrenalins at the back.

Had real problems keeping traction to the ground, so I reckon my time can definately be improved on.

Nice, close to the magical 100mph.

You RB20 boys make me sad ;) stupid heavy ass 34s :P

Def will get a high 13 with a good launch.

Its interesting your MPH tho. I ran 99mph with a cat back and around 10ish psi of boost (extra spring on wastegate, so it didnt hold anything like an EBC) - and on the dyno it made just over 160rwkw.

So with my extra weight, 19s etc, hopefully I am maybe 170ish rwkw in fact, to be pulling the same mph. ahhhh who knows.

Either way looks like the Iphon app goes alright sometimes, and not so good others :)

Edited by Granthem
Mate, I'm runnin in my R32 Gtst 14psi, dyno'd at 165.6rwkw/457Nm @ 6500rpm tuned on a 28deg day by Dr Drift and only managed a 14.452 at 98.7mph.

I have a full 3" turbo back, hi flow cat, intercooler, pod, bigger fuel pump & boost controller for the life of me couldn't break the 100mph mark no matter how many times I tried(did 15 runs)

The only way you will know is to get it on the strip & see for yourself- if your up in Qld your welcome to come to our next Drag day & see how you go-we would love to see you there-Qld Events team out :devil:

I ran mine at the same event with pretty much the same mods but with a highflow turbo making 175rwkw untuned ran a 14.32 and a best of 100.90mph.

Now with the car off getting a few upgrades along with a Haltech installed and tuned I'm hoping to get close to the 110mph mark.

what do you guys think my 32 gtst will run with about 210 too 220rwkW?

could have up to 250 when done but that is the most conservative figure i have been quoted

upgrades are:

-rebuilt engine (metal head gasket, rings, ACL bearings, completely recoed head)

-GTR injectors (fresh cleaned and serviced)

-OS Giken Cam Gear on zorst side

-Gates Triple Strength T/belt

-FMIC

-Walbro 550hp fuel pump

-sard fuel reg

-full zorst, no cat (shhhhhhh)

-pod

-KKR430 turbo

-Microtech LT16S ECU tuned by Tony Rigoli Performance

phew lol

so i wanted high 12s...think thats possible on coilovers and second hand 235s?

also what power figures sound more on key?

gotta beat my mates 6litre HSV Maloo lol

what do you guys think my 32 gtst will run with about 210 too 220rwkW?

could have up to 250 when done but that is the most conservative figure i have been quoted

upgrades are:

-rebuilt engine (metal head gasket, rings, ACL bearings, completely recoed head)

-GTR injectors (fresh cleaned and serviced)

-OS Giken Cam Gear on zorst side

-Gates Triple Strength T/belt

-FMIC

-Walbro 550hp fuel pump

-sard fuel reg

-full zorst, no cat (shhhhhhh)

-pod

-KKR430 turbo

-Microtech LT16S ECU tuned by Tony Rigoli Performance

phew lol

so i wanted high 12s...think thats possible on coilovers and second hand 235s?

also what power figures sound more on key?

gotta beat my mates 6litre HSV Maloo lol

All the guessing in the world won't make any difference in your life unless you actually do it for real. What is happening with you guys these days ? What's next, asking if you could sprint 100mtrs in 7sec if you were wearing so and so shoes and had your hair parted in the middle for less wind resistance ? Perhaps if I tell my phone I weigh 100kilos and can leg press 600lbs for 12 reps @ 8% body fat I could get that down to 3 seconds.

These guessing gadgets are useless. Get out there and as Nike would say, "just do it".

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...