Jump to content
SAU Community

Recommended Posts

Yeah mate same boat here, i have a power fc though and i think its something do do with fuel/ignition timing vs intake temps on startup?

never sure but last 2 days its been hot and my car has taken a couple of attempts to start.....same in very cold-start conditions.

:D ignition module or coil packs or something else???

any help appreciated

What ECU do you have?

Yeah mate same boat here, i have a power fc though and i think its something do do with fuel/ignition timing vs intake temps on startup?

never sure but last 2 days its been hot and my car has taken a couple of attempts to start.....same in very cold-start conditions.

Go into 'settings' then 'cranking' and have a look at the 50deg and 80 deg settings.

Change the 80deg to 9.0 and the 50deg to 10.0 and see if it starts easy for you.

Go into 'settings' then 'cranking' and have a look at the 50deg and 80 deg settings.

Change the 80deg to 9.0 and the 50deg to 10.0 and see if it starts easy for you.

oh mad, ill take a look at my controller and report back. Thanks man

Apexi power fc, nah mine wont start at all when its hot.

Bought an fitted a new ignition module wasn't that. it was a waste of $900

still have to push start it when its hot :D very embarrising in the middle of town.

ordered new set of splitfires should arrive tuesday

*oh sorry i meant when the engines hot not the air temp.

Edited by Country Cruzin

yeah i agree with stevel, sounds like its the starter motor, make sure your alternator is also working though and your battery is ok. should be 13.6ish-14.5ish volts when the car is running(at the battery). and if your battery is over 3 years old id almost consider it f'ed.

Im very confident its the starter motor. I had the same problem 2 years ago when i had a FORD PROBE. Same deal, wouldnt start on odd occasions. Changed the starter my self (easy to do) and the problemm was fixed. Give it a go i say

Apexi power fc, nah mine wont start at all when its hot.

Bought an fitted a new ignition module wasn't that. it was a waste of $900

still have to push start it when its hot ;) very embarrising in the middle of town.

ordered new set of splitfires should arrive tuesday

*oh sorry i meant when the engines hot not the air temp.

wont be coil packs either as others have said... push starts = starter motor.

my mate had this issue, check this thread out

http://www.nissansilvia.com/forums/index.p...=356831&hl=

"yea i had this issue on my rb it was voltage drop ( once the car gets hot the power to the starter is actually less cause the voltage has more resistance in the wire)"

:) No not the starter motor, motor turns over quite easily for the first six attempts than starts to slow down as the battery gets flatter. just wont fire up.

the reason i think it could be the coils is it runs fairly rough on idle after driving/thrashing it for a fair while, seems to miss a bit down low.

only started doing it since i had a lot of work done to it boost turned up to 20 psi ect. the mechanic said the coils mightn't keep handling it.

an that was his guess of the problem.

did you try changing the cranking values as dan said - I have had this exact problem you are describing put up with it for months till I called into ERD last weekend and he has the car hot starting in a matter of minutes...

I have the same problem starting mine when its hot. Not the starter motor as the engine turns over fine. If i don't get it started on the first attempt, it wont start at all....just keeps turning over...

However (don't ask me how i figured it out), if I disconnect the first injector and try again, she will start, then I plug in the injector power again :D:(

I reckon it is over fuelling or something because I can smell the fuel in the engine bay, and black smoke comes out of the exhaust after it starts.

Any other ideas?

BTW im running a NISTUNE remap. Would take it back to the tuners but some 'champ' rear ended me so I have been following that up....

Reason is Starter motor, I have it right now.

Unfortunately the starter is fairly expensive. Either the heat shield has been removed in perhaps a clutch install or the starter is shitted itself.

it will eventually die, until then it may start with abit more gas and longer ignition.

secondly its not the tune... at all.

douse sounds like a fueling issue with ur car.

to fix replace starter, install a heat shield. it stops working because the starter absorbs heat and it requires more power to fire. you may want to try run a bigger ground first, check the power at the starter first warm vrs cold. or perhaps warm car up let it sit for 20-30 mins when it absorbs most heat and then hook up a jump start see if it fires then this may mean the battery is rooted.

What ECU do you have?

Go into 'settings' then 'cranking' and have a look at the 50deg and 80 deg settings.

Change the 80deg to 9.0 and the 50deg to 10.0 and see if it starts easy for you.

My 33 has a PFC. When it's really cold it cranks and starts but I have to keep revs up above 1000RPM for a few seconds with the throttle, otherwise it sort of bounces revs and stalls.

Is this a cure or any other ideas???

Cheers,

Ben

However (don't ask me how i figured it out), if I disconnect the first injector and try again, she will start, then I plug in the injector power again :D:P

I reckon it is over fuelling or something because I can smell the fuel in the engine bay, and black smoke comes out of the exhaust after it starts.

Sounds like a faulty temp sender. The ECU thinks the engine is still cold, so it adds lots of fuel for a "cold start"

Go into 'settings' then 'cranking' and have a look at the 50deg and 80 deg settings.

Change the 80deg to 9.0 and the 50deg to 10.0 and see if it starts easy for you.

will this change the tune at all??

dont know much about tuning at all, just know it was dyno tuned for hours an was told that, down low on cruise he has kept it as lean as possible an at 20 psi its running rich but on its limit of knocking. an a slight change to the tune an the engine's buggered.

still waiting on new coils should arrive any day they've bn sent. other wise i'll have to plan a trip back to brissy an let mark figure it out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
    • Did you even watch the video? Its not a steering wheel. 
×
×
  • Create New...