Jump to content
SAU Community

My Stagea Is Dead....

CL11QE

By CL11QE,
in Four Door Family & Wagoneers

 Share

Recommended Posts

66yostagea Grand Master

66yostagea

Posted
Posted

Have you washed the engine bay with fairly high, hose, pressure. If water can get in anywhere this could cause the prob.

Also have you discon the battery pumped the brakes a few times to reset the ecu?

CL11QE Proficient

CL11QE

Posted
  • Author
Posted
Have you washed the engine bay with fairly high, hose, pressure. If water can get in anywhere this could cause the prob.

Also have you discon the battery pumped the brakes a few times to reset the ecu?

no cleaning of the engine with a hose at all....

is that all u have to do to reset the ecu?

GoldZilla Grand Master

GoldZilla

Posted
Posted

It was an engine fuse, Hugh. We got that sorted out and now the battery light is on. Hopefully that's just another fuse issue or at the worst just the regulator on the alternator...

CL11QE Proficient

CL11QE

Posted
  • Author
Posted
check your fuse for the horn isn't blown

i actually had the fuse for my horn out, i had to use it for the engine one that had blown until i could get a new one....i replaced it last

night at the same time as i gave the terminals a good clean so i cant say 100% which act it was, unless u can tell me the horn fuse being

out would cause the battery light to come on?? why on earth would that be??

Topkart R33 Community Regular

Topkart R33

Posted
Posted
i actually had the fuse for my horn out, i had to use it for the engine one that had blown until i could get a new one....i replaced it last

night at the same time as i gave the terminals a good clean so i cant say 100% which act it was, unless u can tell me the horn fuse being

out would cause the battery light to come on?? why on earth would that be??

It would run in series with the alternator cct.......a very weird way of doing it but that is just the way it is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
×
×
  • Create New...