Jump to content
SAU Community

The Hoon Laws In Practice

MLCrisis

By MLCrisis,
in New South Wales

 Share

Recommended Posts

MLCrisis Proficient

MLCrisis

Posted
Posted

Hi, all. You all know about the issues we have with the "Hoon Laws". Now is your chance to do something about them. This thread is for New South Wales to gether information about the practice of the hoon laws in your state. This is what I said in the similar thread, now a sticky, in WA:

I believe that the "hoon" laws are badly drafted and give the police far too much power. They are bad law! There are sufficient laws without them. The rules of evidence are also being seriously diluted by pursuing convictions on the word of members of the public. Little old ladies phoning up to say "he was going very fast" should not constitute sufficient evidence. Hopefully it does not, but we shall see.

Populist measures are too easy for politicians, but by implementing such poorly thought out laws those politicians fail to do their duty to ensure that the laws they enact are sound. If they are not sound, they bring the whole system into disrespute. More particularly, they place the Police in the impossible position of applying those laws in an impartial manner, when their human frailty means falling short is inevitable. Hence, they themselves become undermined by the very position that these laws put them into.

I would like to compile evidence of the hoon laws in practice. So if you know of poor application of the law, inappropriate actions by police using the hoon laws, the use of questionnable evidence, or similar, please let me know via this thread and/or pm. Please only first hand experience - not "I know a bloke, who's mate's girfriend's brother".

If we compile sufficient evidence, I intend to put a submission to the Government to change the law. Let the punishment fit the crime!

If anyone else has experiences they are prepared to share, please add them on. Good experiences as well as bad. If you were done fair and square, then please say so. If the policeman was reasonable in his/her behaviour, please say so. If they were aggressive and overbearing, let us know. If you were aggressive and disrespectful, let us know. Best to have basic facts here and more detail in a pm.

Thanks everyone. Please note that I am not knocking the Police, they do a hard job that not many people would do. But a badly framed law allows them to overstep their real powers and some of them will use it - because they are not all saints!

So there you go. We need good data to support our argument. We need information in each state to fight this, as no state government will want to go it alone in repealing them.

Please be careful in what you post. This is not intended to be a thread for you to rant or argue. It is to gather facts.

Thanks guys. Go to it!!

Cheers. :yes:

Link to comment
https://www.sau.com.au/forums/topic/254558-the-hoon-laws-in-practice/
Share on other sites
Kujotk Grand Master

Kujotk

Posted
Posted
Unfortunately it has turned into little more than a cop bashing thread on NS with no input into your issue whatsoever.

Will that happen here?

its upto the administrators to keep out the filth and give people warnings or suspensions if they continue to insight a fight or an arguement. The most of us are decent people, usually the trouble makers specifically sign up to argue, you can spot these people by being non SAU members who on their first few posts try to make an arguement or knock a group of people to start a debate.

I'm pretty sure the admins will keep a close eye on what is said in the NSW section, they always do.

offcorse there will be some "cop bashing" when people are frustrated, but i'm sure it will be better tastefull than NS

also can't believe you compared us to NS in the first place, should get a warning for that lol jkz

  • 1 year later...
MLCrisis Proficient

MLCrisis

Posted
  • Author
Posted

Firstly, my apologies for not checking up on this thread for a while!! I realise that the laws are different from state to state and that NSW may not have the same issues - yet. The point is that the various versions of these laws around Australia all share the same key characteristic - that they are fundamentally unjust and unsound and represent an attack on civil liberties. I have no doubt that many young drivers, whatever their ride, are irresponsible and need to be brought to book in some way. However, the standard laws already on the statute, for dangerous driving, reckless driving, etc. present sufficient means for that, without the imposition of laws that allow unfettered discretion to the boys in blue.

I would add that I am unable to spend the time checking threads in each state's area (daft idea, really) so I will leave this thread to those in NSW who care to think about the matter. Perhaps there are some amongst you who will appreciate the greater issue, see it as something worth fighting for and take that fight on in your own way.

Cheers. :laugh:

The Bogan Grand Master

The Bogan

Posted
Posted

The laws will remain and/or get even tougher because of idiots drifting around roundabouts or boosting down 50kph streets, its not just imports, the holden and ford guys are just as bad, my fav at the moment is the guy in his stocko camry who is either on the gas or on the brake, the sooner he takes himself out the better the world will be.

As a father Im all for crushing cars of idiots who do stupid shit on the street, Im not talking about doing 10kph over the speed limit but 100kph in a 50kph area.

If they just killed themself I wouldnt care but they kill passengers and pedestrians.

MLCrisis Proficient

MLCrisis

Posted
  • Author
Posted
As a father Im all for crushing cars of idiots who do stupid shit on the street, Im not talking about doing 10kph over the speed limit but 100kph in a 50kph area.

If they just killed themself I wouldnt care but they kill passengers and pedestrians.

And, if you will forgive me, that is the problem with these laws. They present a populist "solution" to a problem that, in the main, is a social nuisance, but also has elements that endanger innocent bystanders. The problem is the way they are enacted. They give too much discretionary power to the policeman on the spot. You are guilty until you are proven innocent and, in most instances, it is almost impossible to prove your innocence because it is your word against a policeman - and naturally the policeman is going to demonstrate he was correct.

So I agree that the idiots who drive dangerously should be taken off the road. But that should happen in a way that is just, has appropriate judicial oversight and safeguards and provides punishment that is in proportion to the crime.

Cheers. :down:

CARSICK Rising Star

CARSICK

Posted
Posted

Hypothetical scenario...

Hoon gets picked up doing his thingy

Cop tells him to hoon on the track>

Judge tells him to hoon on the track>

Record states he's been told 2X to hoon on the track>

Hoon's car gets confiscated for a month if it's his car + Fine + Points/Loss of Lic.

Hoon gets picked up again>

Judge reviews his record>

Car gets confiscated and sold off; and proceeds go to road upgrades.

MBS206 Grand Master

MBS206

Posted
Posted

The only people I've heard of, who have had issues, deserved it. They were known to the police, had a history of idiodic driving etc etc.

Secondly, the police can pull you over, book you for neg, wreckless driving, speeding etc, and do you know the funny part, they might book you for neg driving, speeding and not wearing a seatbelt and that gives them enough points for some people to loose their licence for 6 odd months (Sometimes more!)... The Hilarious part... The fact that the copper then just has to walk away, and joe blow idiot is free to rip a skid and take off up the street and keep going LEGALLY for another month or two...

It is only in the VERY rare instances that Police can and will confiscate a licence on the spot. If they take the car away, for most people it makes it ALOT harder for them to do this.

So car gone for a month, can't drive, then loss of licence for 3 - 6 months, hopefully if they're smart enough (Most aren't) they won't drive, so it frees the roads up for 4 to 7 months.

Also, the only time I had an over bearing/aggressive copper was when I was caught well and truly over the speed limit, he went all "you were going real fast back there, how fast do you reckon you were going" and I went on the defensive of "I don't know"... Only time I had an issue. The last time I got caught I handed over my licence, apologised, he handed licence and fine back and I was on my way. (Minus 8 points and a chunk of my pay... Damn double demerits!)

The time before that, which could well have ended in a car confiscation ended up with nothing more then a warning as I was polite and upfront. (I could have been booked at 30+ over the limit as I even said a speed to the officer and he let me go after a quick check of my tyres and licence.

Only those whom deserve it, and those who give the coppers hell from what I've seen and heard appear to have these issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DominusUniversi
      R32 Skyline Interior Door Light Issue

      By DominusUniversi · Posted

      I did end up getting it sorted, as GTSBoy said, there was a corroded connection and wire that needed to be replaced. I ended up taking out the light assembly, giving everything a good clean and re-soldered the old joints, and it came out good.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
    • sinn3r
      R32 Skyline Interior Door Light Issue

      By sinn3r · Posted

      Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • aznriptide859
      How To: "Refabricate" a Stagea 260RS/R33 GTR Speedo Sensor

      By aznriptide859 · Posted

      So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • aznriptide859
      How To: "Refabricate" a Stagea 260RS/R33 GTR Speedo Sensor

      By aznriptide859 · Posted

      So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
×
×
  • Create New...