Jump to content
SAU Community

Recommended Posts

hi folks,

my speedometer in my nissan hatch is out by something around 15 - 18 km/h according to my GPS.

so when I'm doing 100 km/h on the clock my GPS shows my 82 - 85 km/h...

(that is why I never got booked speeding, because I never had the GPS on... >_<

and I was wondering why a truck can overtake me when I'm doing 110)

how could I fix this problem ? is there any chance that this is just a adjustment

of something ?

thanks guys,

zee-german

Link to comment
https://www.sau.com.au/forums/topic/256172-speedometer-is-out-by-15-18-kmh/
Share on other sites

Michael,

Where are you in Sydney?

There is a couple of reasons; 1. The speedo could be knackered. 2. Your tyre size might be wrong. 3. You could have a worn drive gear in the box and it is slipping. 4. The diff/drive gear combination is wrong.

This being said the service manual suggests only one (1) possible option and that is the speedo is faulty.

I'm in Sydney's south west (Campbelltown area) if you want another speedo, I'm sure I would have a spare laying around somewhere from when I had mine rebuilt by Jenesis.

Cheers, D

If the odometer is correct, then all the gearing (tyre sizes, diff ratios) are correct.

The speedo works off a magnet spinning inside a metal "cap". A spring controls the "cap" from just going on and on. With age, I reckon, the spring loses its tension, and lets the "cap" rotate further than it should, thus indicating a higher apparent speed.

If the odometer is correct, then all the gearing (tyre sizes, diff ratios) are correct.

The speedo works off a magnet spinning inside a metal "cap". A spring controls the "cap" from just going on and on. With age, I reckon, the spring loses its tension, and lets the "cap" rotate further than it should, thus indicating a higher apparent speed.

hmmm, sounds good... but it shows me a slower speed... so the other way round.

I know that I have the right tyres on the car. right size ect... just changed them a few months ago.

and the gearing should be ok as well. it is an auto transmission, it works fine and solid.

Michael,

Where are you in Sydney?

There is a couple of reasons; 1. The speedo could be knackered. 2. Your tyre size might be wrong. 3. You could have a worn drive gear in the box and it is slipping. 4. The diff/drive gear combination is wrong.

This being said the service manual suggests only one (1) possible option and that is the speedo is faulty.

I'm in Sydney's south west (Campbelltown area) if you want another speedo, I'm sure I would have a spare laying around somewhere from when I had mine rebuilt by Jenesis.

Cheers, D

hi,

I'm on the other side of the city (north sydney, neutral bay)

I bought this car of an old lady 16 months ago with only 116.000 km on it.

and it drives well... engine and auto sounds solid, just changed the injectors and the waterpump.

but my speedometer problem is since I have this car.

hmmm, sounds good... but it shows me a slower speed... so the other way round.
No, it's not (the other way round).

You said the speedo shows 100 when you are actually - according to the GPS - doing 85. So the spring isn't retaining the speedo needle enough. The speedo is indicating a speed HIGHER than actual. (which is what I believe I said the first time, perhaps not so succintly)

I have always gone by gearbox ratio, diff ratio and tyre diameter with tacho reading. So in a manual you can work out exactly what speed you are doing, but in an auto you have to decide whether the torque converter has locked up.

There are places on the freeways where you can clock time against the actual tyre diameter will drive you at a predetermined tacho indication. But you must have an accurate tacho.

My new Ti hatch in 1984 was pretty close to 50 clicks per 1000. So about 2000

Hi, To check if your speedo is working properly go find a 5km odometer check and record how far your odo shows over the 5k's (do the test at the posted speed limit as speed has no relevance with this test) - if the odo shows around 4.2 k's or even under 4.5k's then the problem is unlikely to be the speedo - if the odo shows between 4.9 & 5.1ks then the speedo is likely to be the problem. If the speedo checks out, then you are looking for a component in the gearing so the speedo cable is not spinning at the correct number of revs/km eg speedo drive, the diff changed to a lower ratio and the speedo drive not changed to suit, or wheels/tyres are not standard but i doubt that as the wheel/tyre combination would have to be a lot smaller than standard to make that much difference - most of us put wider & higher tyres on which reduces the revs per km and this causes the speedo to read slightly slower relevant to actual speed ie more accurately - which is why most speedos have a 5% fast read built in ex-factory. If you need help with correct speedo drive ratio i would need to know your diff ratio & tyre size. Cheers, Tel

Hi, To check if your speedo is working properly go find a 5km odometer check and record how far your odo shows over the 5k's (do the test at the posted speed limit as speed has no relevance with this test) - if the odo shows around 4.2 k's or even under 4.5k's then the problem is unlikely to be the speedo - if the odo shows between 4.9 & 5.1ks then the speedo is likely to be the problem. If the speedo checks out, then you are looking for a component in the gearing so the speedo cable is not spinning at the correct number of revs/km eg speedo drive, the diff changed to a lower ratio and the speedo drive not changed to suit, or wheels/tyres are not standard but i doubt that as the wheel/tyre combination would have to be a lot smaller than standard to make that much difference - most of us put wider & higher tyres on which reduces the revs per km and this causes the speedo to read slightly slower relevant to actual speed ie more accurately - which is why most speedos have a 5% fast read built in ex-factory. If you need help with correct speedo drive ratio i would need to know your diff ratio & tyre size. Cheers, Tel

thank you guys for all the answers ! I will check it with the 5 km test..... :-)

"My new Ti hatch in 1984 was pretty close to 50 clicks per 1000. So about 2000"

What a hoot old man, my new 180B SSS in 1973 used to get 20mph/1000rpm in top (4th) so when I was sailing across Mooney Mooney bridge on F3 at 6750rpm, I sorta understood the fowl looks I got from the boys in blue doing radar duty. lol

Cheers, D

Sorry for hijacking your thread temporarily

my speedo is stuffed with the vl gearbox.

the speedo drive is for 3.45 gears and i have 3.9.

i just work out how fast i am going from the RPM's.

100kmh is 2500rpm in 5th and every 500rpm is 20kmh.

speedos are always wrong from factory.

only shit thing is it clocks up klms quicker on the odo

but who cares. just buy another dash.

My first RMR30Ti had 600 on it when I gave her a decent burial. Changing the speedo is (illegal) a bit of a waste.

"Changing the speedo is (illegal) a bit of a waste".

Not if your old one is broke, it's not.

In NSW the annual rego checks require an odometer reading on the inspection slip, so the RTA knows wether the speedo has changed and or been repaired.

My PNV when it goes on the road will have a Jenesis 260kph speedo with ZERO on the clock & a 9000rpm tacho and that wont be illegal.

I suppose it's a bit diferent for these backward states that don't have regular inspections eh?

Cheers, D

I suppose it's a bit diferent for these backward states that don't have regular inspections eh?

Shhhhh, I like these backward states that don't have regular inspections.

otherwise my turbo conversion may never get done, or my aftermarket ECU, wouldn't past muster (emissions), but then again, I have never looked into what is or is not illegal.

Nigel

"Changing the speedo is (illegal) a bit of a waste".

Not if your old one is broke, it's not.

In NSW the annual rego checks require an odometer reading on the inspection slip, so the RTA knows wether the speedo has changed and or been repaired.

My PNV when it goes on the road will have a Jenesis 260kph speedo with ZERO on the clock & a 9000rpm tacho and that wont be illegal.

I suppose it's a bit diferent for these backward states that don't have regular inspections eh?

Cheers, D

I thought as much, its more illegal to have an odo that is not working.

I think we should have regular inspections. Get all the shit heaps off the road.

Maybe not every year but every three or five years. You see cars driving around

with smashed lights, rust everywhere, some real junk boxes.

skybt1, might I suggest you change the drive in your gearbox to the correct one - the RB30E gearbox should take the same pinions as the old FS5W71B/3N71B/4N71B that the car came with.

Dennis, if you were doing 6750rpm (as indicated on a 1973-accuracy tacho!) in a stock 610 SSS in 4th, then it must have been downhill :blush:

(and you must have been out of your mind)

I've got a 4.375:1 LSD in my DR30, but in order to get the speedo correct (within ~5%) I've had to fit the 4.625:1 speedo drive. A combination of slightly shorter tyres (225/50/16) and a 25-year old speedo have resulted in extra compensation being required to get things right.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...