Jump to content
SAU Community

Recommended Posts

Awesome car!

I, myself took a while to find any info on it. The company is more so a tuning garage for Japanese performance cars and have done afew Euro cars and produce their own cars.

+ their website does not say much about it either and not much info at all on the AWD system tho...

All I know atm is the Tommy Kaira ZZ II was a $90,000 sportcar door coupe production car with a reverse mid mounted RB26DETT with 550hp (410.14 kW), 6 speed manual gearbox, does 0-400 metres in 3.3 secs and weights about 1500 lbs (680 kg) with 6pot front brake calipers and 4pot rear brake calipers.

It also featured front and rear aero diffusers, and a fully built roll cage.

IMO it is one powerfull and lightweighted fast car.

http://www.fast-autos.net/vehicles/Tommy_Kaira/2001/ZZII/

http://en.wikipedia.org/wiki/Tommy_Kaira

:D

Yeah I was suprised too, but its what I could only find on Fast Autos forum...

it was a fun car to drive on GT3 :laugh: well maybe not that particular model

Yes I was a fun car to drive in GT3.

I AM AGREEING WITH YOU! ;)

:D

LMAO! THANK YOU! :)

Thanks SKYLINE i already found out that much, i just want to know how to run the 26 gearbox in reverse and still have 5 forward and 1 revers gears :) keen on building something similar to a ZZII...

As they say "Crazy Japs" LOL! The things they do amazes me too and keeps me wondering.

All I can think of is they have modified the gear setup in the gearbox and the drivetrain...

Anyway all the best on your conversion.

To build one KISIN you would require a totally custom gearbox, the front diff in the sump could be utilised to drive the rear wheels, drive to that diff could be sent in the same way as a normal gtr (just backwards) and forwards to a front diff (which would usually be to the rear) but it would all have to spin backwards, lock the transfer case and be totally modified to have the H pattern shift the correct way around fro the driver. Then you would need to build the car, which you could build as a full spaceframe with intergrated roll cage, then glass fiber body, custom lights, fittings, glass etc...

If you were going to all this trouble you would probably want to register it as an ICV so you can drive it on the road, which, depending on your particular state you would need a suitably new engine, I think 3-4 years old or there abouts with the factory computer and emissions equipment...

You will spend well in excess of 6 figures, mabey even just for the gearbox, and it will take thousands of hours of custom fabrication. Good luck with the project KISIN, keep us all updated with a build log :thumbsup:

it's 0-60ks in 3.3sec..
Im sure they meant 0-100km/h in 3.3....

400mtr is a qtr mile...

Yeah my bad LOL! 0-100km/h in 3.3 secs. I don't know about the quater mile... Damnit can't edit my post...

In USA it would be 0-60mph in 3.3 secs.

To build one KISIN you would require a totally custom gearbox, the front diff in the sump could be utilised to drive the rear wheels, drive to that diff could be sent in the same way as a normal gtr (just backwards) and forwards to a front diff (which would usually be to the rear) but it would all have to spin backwards, lock the transfer case and be totally modified to have the H pattern shift the correct way around fro the driver. Then you would need to build the car, which you could build as a full spaceframe with intergrated roll cage, then glass fiber body, custom lights, fittings, glass etc...

If you were going to all this trouble you would probably want to register it as an ICV so you can drive it on the road, which, depending on your particular state you would need a suitably new engine, I think 3-4 years old or there abouts with the factory computer and emissions equipment...

You will spend well in excess of 6 figures, mabey even just for the gearbox, and it will take thousands of hours of custom fabrication. Good luck with the project KISIN, keep us all updated with a build log :thumbsup:

Interesting... Sounds like you done it before?

Yes updates will be good.

To build one KISIN you would require a totally custom gearbox, the front diff in the sump could be utilised to drive the rear wheels, drive to that diff could be sent in the same way as a normal gtr (just backwards) and forwards to a front diff (which would usually be to the rear) but it would all have to spin backwards, lock the transfer case and be totally modified to have the H pattern shift the correct way around fro the driver. Then you would need to build the car, which you could build as a full spaceframe with intergrated roll cage, then glass fiber body, custom lights, fittings, glass etc...

If you were going to all this trouble you would probably want to register it as an ICV so you can drive it on the road, which, depending on your particular state you would need a suitably new engine, I think 3-4 years old or there abouts with the factory computer and emissions equipment...

You will spend well in excess of 6 figures, mabey even just for the gearbox, and it will take thousands of hours of custom fabrication. Good luck with the project KISIN, keep us all updated with a build log :thumbsup:

Thanks for the reply. Ive already found someone that can build me a chassis and another for the body. Very good points you bring up, ICV - thats the path i hope to take, but 6 figures, maybe just for the gearbox ???

Apparently a company in the US can build this for me "no problems at all", however unless i see one of their models working, im not ordering anything with the aussie $$ this weak...to their credit though, ive seen their other work and its pretty damn good, even modified a lambo for SEMA...According to them, its piss easy to get it to work.

Just had a thought - the porche 4wd gearbox could be worth looking at, I think porche engines spin the right way, then the drive to the front wheels will be fine, H pattern is ok, the only trouble would be building an adapter plate to mate to the RB, and sending drive rearwards - you would need to remove the rear drive diff in the gearbox and send drive rearwards with a driveshaft - being very careful of final drive ratios, but they should be able to handle the power straight out of the box. Also you could even use one of the flappy paddle gearboxes for extra techy'ness.

*dont underestimate the cost of a gearbox for such a project - it will probably be the most expensive single part!

If you are keen to register it, talk to your local transport authority about building an ICV and they will point you in the direction of approved engineers to help you :D

Just had a thought - the porche 4wd gearbox could be worth looking at, I think porche engines spin the right way, then the drive to the front wheels will be fine, H pattern is ok, the only trouble would be building an adapter plate to mate to the RB, and sending drive rearwards - you would need to remove the rear drive diff in the gearbox and send drive rearwards with a driveshaft - being very careful of final drive ratios, but they should be able to handle the power straight out of the box. Also you could even use one of the flappy paddle gearboxes for extra techy'ness.

*dont underestimate the cost of a gearbox for such a project - it will probably be the most expensive single part!

If you are keen to register it, talk to your local transport authority about building an ICV and they will point you in the direction of approved engineers to help you :D

Already had a chat to the transport department regarding ICVs and the gearbox is what im worried about the most !

hahaha.. post up pics of the build when youve got everything!

would be interesting to see it.

Well i have a fairly unique body *hopefully* getting made and right now i know there will be many haters because of what it will "copy" so to say...but im building MY dream car for ME :domokun: Hoping to have this baby done in a couple of years (yes couple, and thats pretty quick if you ask some others who have built cars from scratch). Pretty close on striking a deal with the US company, just the body is holding me back...you'll see why 1 day lol :) Until then buying an investment property to help fund this sucker !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
    • This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
    • Unfortunately the cavaet to that is that while any scan tool should be able to read the code, the workshop will need a consult plug to OBD socket adapter. You don't have a location on your profile, where are you based?
    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
×
×
  • Create New...