Jump to content
SAU Community

Recommended Posts

  • Replies 2k
  • Created
  • Last Reply

Top Posters In This Topic

chu_rulz- this is a mission, engine alone will set you back from $6500, then you need a rb25 gearbox to run it in rear wheel drive only about $2000/guesstament, drive shaft, diff $??, fuel pump $450, gtr fmic and custom piping $1500, a serious brake upgrade lets say $3-4000 custom job, new 3" exhaust dump pipe back $1500, good syspension may be tag on another $1000+ to the brake upgrade as these two may go hand in hand and don't forget unless your doing all this your self you'll be paying someone to do it for you$$$ lifes a bitch!

In the long run if you do it all right the first time you'll have one of the fastest cars, after just a ecu mod or swap, in the skyline family!

have you got the latest zoom with the r31 on the cover, if not i'll scan it and pm it to you as the r31 has done a rb26 swap!

Hey guys.... I tried to install a boost controller on my HR30 and i have run into a few problems.

today i was attempting to install my Turbosmart gated boost controller with my mate, and we didnt have much success. It has a triple hybrid turbo. the compressor is standard i think and the exhaust is from some comodore. the response was very out of wack and sometimes it wouldnt come on boost at all. basically it was behaving nothing like it should, and we were 100% sure of all installation points... any ideas??

we also after having no success with the first item, tried another model that my freind had awaiting employment in his car, and had the exact same result. we had not turned up the boost at all, and it was behaving very oddly.

any help PLEASE!

Also why is there a tee coming from the compressor housing and the outlet pipe and feeding the wastegate actuator? Isn't there normally only one coming from the outlet pipe and feeding the actuator?

do they both need to be connected or can i block one?

I really need some advise on this. Any help would be much appreciated. :D

there are things to remember when increasing boost, its all good to play around with boost levels, but if the ecu is set for X amount of boost then X amount is the best. don't get me wrong the l20et turbo is not runnig a ceramic shaft so boost can go, but if theres no fuel theres no fuel, did you take a boost reading to start with?

there are things to remember when increasing boost, its all good to play around with boost levels, but if the ecu is set for X amount of boost then X amount is the best. don't get me wrong the l20et turbo is not runnig a ceramic shaft so boost can go, but if theres no fuel theres no fuel, did you take a boost reading to start with?

i'm not playing around with it yet though. i just hooked it up and was running it on standard boost so it should make no difference.

Ok,did you follow the guide you got with the boost gate as i bought one today/24/12/03 and have read the guide today and it states start from 0, there are things to cross out?

I got the car very resently and the car came with a boost controller and just that nothing else. i don't have them. is there anyway you could send them to me?

cool no dramas

i might just take it to a suspension dude and give them the parts i got and tell them what i want done

any thought on how much injector collars cost? L24 im talkin about,

3 of mine are fugged and the orings are gorn...ie leaking

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...