Jump to content
SAU Community

Recommended Posts

the 'fluttering' that i think you are describing is called 'compressor surge'. it happens when the bov it sprung too tight or when you don't have a bov (ie not a skyline).

when the throttle body closes (like taking the foot off the accelerator), the comressed air hits and reflects back in the direction it came. in a skyline the bov would open and air would pass out through this making a 'ppsssssshhhhhhhhhh' sound. if no bov, then the air goes back through the intercooler and passes through the compressor side of the turbo in the opposite direction to the spinning blades and as mentioned by obseshn this 'chops' the air up making a fluttering noise. as you can imagine it ain't good for the turbocharger even if it sounds good.

hope that helped.

Waz.

Have a friend who ran a turbo for quite a while with no BOV and it was still fine. Unsure about my car but it's making a fluttering/chattering/chopping noise so either the BOV's pretty tight or the previous owner removed it. Will have to perform a more thorough investigation but everything's in good nick!

definitely not wastegate. on closed throttle there's no air going through the engine so the wastegate opening and shutting wouldn't do much. Either the BOV fluttering or compressor surge with air reverting back through the turbine compressor blades.

This "fluttering" is also a major factor in engine stalls when comming to a stop. I was investigating stalling issues on my car a while back and did some measurements with an oscilliscope on the AFM. I've attached an image of AFM voltage with a "loose" and "tight" BOV. Note that the "tight" setting produced audible "flutter" through the AFM after a rev, and this is seen as the severe oscillations in the trace indicating reversion due to compressor surge....

phantom

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...