Jump to content
SAU Community

Recommended Posts

Hi guys, I posted this in another thread but it's a little obscure if anyone was wanting to find a how-to. I searched and found zip so thought I'd snap some pics of mine I did todday.

** I used two different size hole saws to cut the radii and simply used a cutting wheel to remove the rest. Lots of masking tape around the area to stop any damage from swarf.

Initially I mounted the pins, raised them a little to make contact with the bonnet and make a mark from inside. I then drilled a small pilot hole, and then masked on the template provided and went from there.

Measure six times, cut once I suggest! :thumbsup:

Made U shaped brackets to utilise an existing hole in the radiator support. The return down the front too to give some extra strength. Made these from 3mm steel. You can see I had to gring the bolt down a little to allow clearence.

22022001.jpg

22022003.jpg

This is the drivers side from under, nothing tricky really.

22022009-1.jpg

The passengers side was a little harder. I did this second to get the feel for it. This is a GTR bonnet so I hade to carefully remove some of the reo.

22022002.jpg

And the finished product! A bit of fine tuning is needed to get them just right, and it's very strong, not going anywhere. As a bonus the rubber stoppers they supply were the perfect length to allow a little preload so no rattles.

22022004.jpg

22022005.jpg

And a reminder that angle grinders with cutting wheels can bite.

22022006.jpg

Link to comment
https://www.sau.com.au/forums/topic/258154-aerocatch-bonnet-pins-into-an-r32/
Share on other sites

What a great read!! Came up really well...

I did the same thing 3 months ago, although mine is a fibreglass/carbon bonnet, so would have been easier to cut.

They work so well and look much cleaner than the old bonnet pin style..

Here's my finished result...

gallery_1569_106_158120.jpg

Was going to get my panel beater to paint them silver but he advised not to, paint might not stick properly and would most likely peel off from constant use...

Either way they're not as noticeable as the old bonnet pins, especially since it gets driven on the street...

i put these on my 32. the bonnet i used had all the supports cut out so i didn't have to make it fit around them.

the car also had had bonnet pins so i used the holes in the radiator support panel to fit mine but as you may have found it a bit to shallow under the bonnet to fit them so my bonnet which isn't real straight anyway doesn't quit fit flush. if i get a new bonnet i will install them the way you have.

oh and word of warning after a bit of work the lock in pins start to over balance and you need a tool to get them to lock down. i am not the only one to have run into this.

i got mine after seeing all the cars in targa tas last year with them and funnily enough your going in targa tas with some.

so these are regarded as street legal? Where did you get them?

yeah as they are flush fit on the surface of the bodywork most states accept these as road legal.

bensonmotorsports.com was the source for the woo... always in stock!

Nice one.

I have finally taken delivery of my carbon bonnet and a set of these bonnet pins.

I'm going to get Micolor to do it though as I would just mung it up if I attempted it.

Kudos to you for taking the time to do it yourself.

Regards

Andrew

Looks good, one of the more subtle ones which seems to suit the R32 better. How strong are the carbon bonnets with using Aerocatches. Is the carbon too rigid and brittle ?

No idea, it's got all the factory latches as well so it should hang together. the pins are only insurance.

great write up mate!

love these pins! so much tidier than the metal ones...

angle grinder = OUCH! hope your hand heals quickly...

I bought a set for my s13 a while back, but another "wooss" here

I took the easy way out (had my panel beater fit them while my car was in paint)

even he was nervous and he couldn't promise me a 100% guarantee on perfectly straight and flush fitment, but he nailed it first shot...

at first i was concerned they might bind up or become brittle, after sun/water/soap/dirt/dust etc but they are well made and with a tiny spray of wd40 stay nice and operable.

the only thing i could put them down for, is the pins themselves, they could be swapped out for some actual steel ones...

some pics from when i had mine done:

2008-03-12015.jpg

2008-03-28041.jpg

pins2.jpg

I tried to use some about 3 years ago but woosed out because i didnt want to cut up my GTR bonnet...maybe its time to second guess that decision :thumbsup:

lol, just bite the bullet Roy and do it mate, they look great and operate smoothly. I reckon they're the best part of the car now :D

Oh, guess what, the wheel Just turned up :D

If anyone needs it, i just made up a cutting/drilling template for the 125 Series, the one they supply is for the 120 series and slightly different.

Print it out full size and you should be sweet :(

Aerocatch_template.PDF

Ok, then where is the quickest and easiest pace to get them. Better shoot them off to the panel beater before the bonnet gets sprayed. Stuart?

They may look ok on my car since i am doing the fan boy black and silver thing :thumbsup:

Troy, got mine through revolution racegear, about $120 from memory....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
    • Trailer got new mudguards to accommodate the new wheels Lightweight ally Painted, stickered and done ✅ 👌  
×
×
  • Create New...