Jump to content
SAU Community

R33 Gtr V-spec For Sale $12000 Complete Or Sell Parts.


Recommended Posts

Car was in an accident Dec last year.

Is classed as a repairable writeoff, has only body damage( both rear guards, roof, passenger door).

All brakes, suspension, steering 100% ok.

Car starts and drives but has no wheels.

Would prefer to sell complete for $12000 ( do the math, its very cheap)

But will seperate parts.

Sell engine complete for $8500

Engine dynoed at 290 awkw @ 15 psi ( all works by Mercury Motorsport)

2 x Garrett 2860 400hp

650cc Sard injectors

Tomei pon cams type b with Tomei adjustable cam gears

N1 water pump

JJR coils

clear gear cover

new o2 sensors

new rear main oil seal

new plugs, oil, filters

comp test and inspection welcome

Nismo intank fuel pump $200

Ceramic coated dump pipes (twin style) $600

80mm exhaust with high flow cat $300

quality 600 x 300 x 75 intercooler $200

Had brand new g/box (Nissan) and clutch fitteed the day before the accident.

gearbox cost $3500 + $280 for nismo g/box mount sell for $2800

Jim Berry 4400lbs single plate clutch cost $950 sell $650

Brembo calipers and good rotors $1500

Earls braided brake lines $200

400r front bar (slight damage) $300

Veilside rear bar $350

Veilside skirts (one broken in half) $150

2 x guards $100 each

bonnet $150

Grille $40

Head lights $100 each

nismo clear indicators $50

Drivers door with mirror $250

new alarm cost $450 sell $200

Airbag boss kit cost $200 sell $100

new battery sell $80

centre console with new leather gear boot $150

centre gauges $50

Rare Mines 320 klm dash $500

Drivers bucket seat $350

New still in box Power FC boost controller $500

too many other parts to list

Phone Ross 0402 162 488

pickup Brisbane North side

yes pics please, detail on the damaged areas would be good too...

so no wheels with purchase???

im also on northside, what suburb is the car in???

pics will be up tomorrow

thats right no wheels

Im in Joyner, near Warner

[photos added]Car was in an accident Dec last year.

Is classed as a repairable writeoff, has only body damage( both rear guards, roof, passenger door).

All brakes, suspension, steering 100% ok.

Car starts and drives but has no wheels.

Would prefer to sell complete for $12000 ( do the math, its very cheap)

But will seperate parts.

Sell engine complete for $8500

Engine dynoed at 290 awkw @ 15 psi ( all works by Mercury Motorsport)

2 x Garrett 2860 400hp

650cc Sard injectors

Tomei pon cams type b with Tomei adjustable cam gears

N1 water pump

JJR coils

clear gear cover

new o2 sensors

new rear main oil seal

new plugs, oil, filters

comp test and inspection welcome

Nismo intank fuel pump $200

Ceramic coated dump pipes (twin style) $600

80mm exhaust with high flow cat $300

quality 600 x 300 x 75 intercooler $200

Had brand new g/box (Nissan) and clutch fitteed the day before the accident.

gearbox cost $3500 + $280 for nismo g/box mount sell for $2800

Jim Berry 4400lbs single plate clutch cost $950 sell $650

Brembo calipers and good rotors $1500

Earls braided brake lines $200

400r front bar (slight damage) $300

Veilside rear bar $350

Veilside skirts (one broken in half) $150

2 x guards $100 each

bonnet $150

Grille $40

Head lights $100 each

nismo clear indicators $50

Drivers door with mirror $250

new alarm cost $450 sell $200

Airbag boss kit cost $200 sell $100

new battery sell $80

centre console with new leather gear boot $150

centre gauges $50

Rare Mines 320 klm dash $500

Drivers bucket seat $350

New still in box Power FC boost controller $500

too many other parts to list

Phone Ross 0402 162 488

pickup Brisbane North side

post-45687-1235777941_thumb.jpgpost-45687-1235778273_thumb.jpgpost-45687-1235778320_thumb.jpgpost-45687-1235778382_thumb.jpgpost-45687-1235778423_thumb.jpgpost-45687-1235778506_thumb.jpgpost-45687-1235778552_thumb.jpgpost-45687-1235778598_thumb.jpgpost-45687-1235778659_thumb.jpg

Edited by r33 ross
  • 1 month later...

is the bonnet straight, any dints as i am looking for a grt bonnet that i can just paint and put on if there are no dints and it is straight pm me

  • 1 month later...
  • 2 weeks later...
  • 3 weeks later...

I will call you today I want the bonnet, the bonnet hinges, guards, guard risers, indicators, and bonnet latch and the strut it is connected to please



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...