Jump to content
SAU Community

Rb25det How Quick And What Weight?

passin ewe

By passin ewe,
in Western Australia

 Share

Recommended Posts

passin ewe Proficient

passin ewe

Posted
Posted

I'm strongly sonsidering putting an RB25 Det into my Datsun Syyline. What I want to know is what 1/4 mile times do you do in a stock or semi stock ( maybe turbo upgrade) skyline with RB25DET.

Also what is the kerb weight of your car, mine being 1260 kg I'm trying to get an idea of power to weight ratio. Cheers

Link to comment
https://www.sau.com.au/forums/topic/261466-rb25det-how-quick-and-what-weight/
Share on other sites
  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

r33-ml Apprentice

r33-ml

Posted
Posted

hay mate .. i done 13.9 with my r33 .. full zorst , pod , cooler and a clutch .....

donno if thats good or not but i was happy ...

now im thinknig of getting a hi-flow turbo , safc and i got a bosch fuel pump so should do a lil better ..

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

The quickest time I've seen with a completely stock R33 is 13.4, and I've seen high 12's with mods but stock turbo. Weight of an R33 is around 1470kgs, so with lighter weight you could expect better results, assuming you can get traction etc.

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted
Where did you see it do a 13.4? R34 GTR's only do a 13.7 pass or so it says...

Almost stock R32 GTR's have done high 12's, so who's driving the R34 :thumbsup:

It's all about 60' times, if you can get your car to hook up properly with a sub 2.0 60', then your in with a shot of a decent ET. The MPH on a stock Skyline is pretty low.

Tezzah Experienced

Tezzah

Posted
Posted
Almost stock R32 GTR's have done high 12's, so who's driving the R34 :thumbsup:

It's all about 60' times, if you can get your car to hook up properly with a sub 2.0 60', then your in with a shot of a decent ET. The MPH on a stock Skyline is pretty low.

So true

Dani Boi Grand Master

Dani Boi

Posted
Posted (edited)
So true

Post #10

http://www.skylinesaustralia.com/forums/Be...-B-t260897.html

Also states on Imports 101 that they only do a 13.7, I know these are only rough figures and its from the internet so probably not dead right but eh...

Edited by Dani Boi
SKYRYAN Grand Master

SKYRYAN

Posted
Posted (edited)

Yeh the GTR should be a low 13, I did a 13.765 with catback and a pod filter in the gts-t

Old stock R33 fuel pumps will start to fail,

they wont make fuel pressure,

your car will run lean,

and you will get more power

and u will run a mid 13

and ur engine will 'explodey poos

I dunno what engine is in ur datto at the moment, but the RB25 is probably going to be heavier?

You should be right for a low 13 second pass if you did the swap (stock engine/turbo with exhaust)

Edited by SKY RYAN
madbung Grand Master

madbung

Posted
Posted
I'm strongly sonsidering putting an RB25 Det into my Datsun Syyline. What I want to know is what 1/4 mile times do you do in a stock or semi stock ( maybe turbo upgrade) skyline with RB25DET.

Also what is the kerb weight of your car, mine being 1260 kg I'm trying to get an idea of power to weight ratio. Cheers

I'd be trying to get weights for your current eng/trans and also rb25det, trans, rad, fans, loom ect ect ect.

Just a guess, but the rb setup might weigh a tad or 10 more, giving you around the same curb weight or more than the r33.

Still it'd be a fun-different thing when finished.

lcy Rising Star

lcy

Posted
Posted
The quickest time I've seen with a completely stock R33 is 13.4, and I've seen high 12's with mods but stock turbo. Weight of an R33 is around 1470kgs, so with lighter weight you could expect better results, assuming you can get traction etc.

I think the R33 are 1360kg.

From factory is was quoted 0-400 = 14.4.

No offence but how would a completely stock R33 would run 13.4?

Pal Veteran

Pal

Posted
Posted

actually,my nephew done the 13.3 when skyryan went down the drags a few weeks ago. he had the white r33 gtst with black mags. would have only had 200 rwhp - 220 rwhp. depends on suspension and 60" times. i had 290hp and could'nt crack a 13. skylines a 1490kg manual and 1520 auto.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...