Jump to content
SAU Community

Recommended Posts

hey, i ve got a r33 rb25det..

for lik a week now..ive bein noticing weird hesitation..well more like little missfires.. or splutters would be the word im looking for..

from i believe it only wen de-acceleration..

lik ive back off the throttle to like change gear for example..or just back off...

but wen i go to accelerate again..it does it..so its not a boost thing..

and im not acclerating hard or full throttle..like 10-20& throttle...so like just from daily driving...so im not evan close to hitting boost..

my mates reckon it sounds like a vac leak..

wen driving..the only thing i can describe it just feel lik ive dropped in power for lik a spilt second...u can feel it in the accelerator pedal...and u can hear here abit..

well the splutters..

but not all the time does it do it...its so weird..

ive changed new plugs and there gap to 0.8m..

clean afm with afm cleaner..

clean iacv wit carby cleaner..

and ive check for vac leak..cant here anything..

did check all silicone hose..just incase and there hose clamps...

and they seem all good...

any ideas?

my engine mods are

walbro fuel pump,fmic,pod,splitfires,apexi afc neo, hks catback exhuast,hypergear atr28 g2 turbo,hdi type-d ebc

could be injectors, could be the tune in the AFC but if it's only been for a week that's not likely. I would suggest having the injectors ultrasonically cleaned. Also make sure your TPS doesn't have a dead spot at that throttle position. Voltage check it while slowly bringing on the throttle.

This happened long time ago to our test car. Its from the turbo's dose. Happens when turbo throws air out to wards the AFM and then suck it back in. After I put the AFM in side cooler piping this issue was solved.

hey 33gtst,,

wat do u mean by low and light throttle cut??wat did it feel like??can u explain it abit more??

or did u have any other noticable issues that appeared too?

thanks

I just had this similar issue, after a tune last week.

last night replaced the spark plugs with new ngk bcpr6e .8mm plugs

had the battery disconnected during the job, reset and its all fine now.

na, its got a atmo bov..

but its set on hard..

so it completely flutters..

but the problem..is on off..

like it will do it lik 1 out 3 days..

sometimes 4 days..

its freakin annoying!

my recommendations

fit the std bov in plumb back mode

replace with a known working AFM

the likely suspect is your BOV, its probably venting vacuum pressure and its enough to annoy the AFM

which makes the car stutter and hesisate

well...i think ive faulted my problem..

i noticed wen on the freeway the other night..

i notice on my afc..that a/f% was on about 10%..then all of a sudden it would just randomly drop to lil 7/8%

nad i could feel the hesitation from this...it did it a couple of times..then it just went away.. ????? :D

but my throttle was in the same position...just cruisin..no boost or anything..

so what i can gather from this this its the afm cutting out..

i just open the silicone top black cover on the top off afm.

noticed the 3 wires that connect to the main board looked fine..

but i still did re-solder them...

and i gave the board a good clean of electrical contact cleaner...

hopfully shes all good now :P

Mine has the same problem, only happens when just opening the throttle off idle or 0%.

I'm running a microtech ecu with no afm.

the cause of mine is the throttle position sensor, i can watch it on the laptop and when the throttle is closed the throttle percentage creeps all over the place until i touch the throttle.

like 3lit3 32 says, "dead spot in the tps"

but at $208 i have not ordered a new one yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • Thank you so much for the help
    • Yes it is ATF. I quote @Duncan "it takes a good synthentic auto trans fluid like Castrol Transmax Z" It's not a diff. It's a transfer case. Totally different thing. Yes, fluid will come out the sender hole. No you do not really need to drain it. Just pull the old, quickly poke the new, clean up and top up. But realistically, you should probably take the opportunity to change it anyway.
×
×
  • Create New...