Jump to content
SAU Community

Recommended Posts

hey, i ve got a r33 rb25det..

for lik a week now..ive bein noticing weird hesitation..well more like little missfires.. or splutters would be the word im looking for..

from i believe it only wen de-acceleration..

lik ive back off the throttle to like change gear for example..or just back off...

but wen i go to accelerate again..it does it..so its not a boost thing..

and im not acclerating hard or full throttle..like 10-20& throttle...so like just from daily driving...so im not evan close to hitting boost..

my mates reckon it sounds like a vac leak..

wen driving..the only thing i can describe it just feel lik ive dropped in power for lik a spilt second...u can feel it in the accelerator pedal...and u can hear here abit..

well the splutters..

but not all the time does it do it...its so weird..

ive changed new plugs and there gap to 0.8m..

clean afm with afm cleaner..

clean iacv wit carby cleaner..

and ive check for vac leak..cant here anything..

did check all silicone hose..just incase and there hose clamps...

and they seem all good...

any ideas?

my engine mods are

walbro fuel pump,fmic,pod,splitfires,apexi afc neo, hks catback exhuast,hypergear atr28 g2 turbo,hdi type-d ebc

could be injectors, could be the tune in the AFC but if it's only been for a week that's not likely. I would suggest having the injectors ultrasonically cleaned. Also make sure your TPS doesn't have a dead spot at that throttle position. Voltage check it while slowly bringing on the throttle.

This happened long time ago to our test car. Its from the turbo's dose. Happens when turbo throws air out to wards the AFM and then suck it back in. After I put the AFM in side cooler piping this issue was solved.

hey 33gtst,,

wat do u mean by low and light throttle cut??wat did it feel like??can u explain it abit more??

or did u have any other noticable issues that appeared too?

thanks

I just had this similar issue, after a tune last week.

last night replaced the spark plugs with new ngk bcpr6e .8mm plugs

had the battery disconnected during the job, reset and its all fine now.

na, its got a atmo bov..

but its set on hard..

so it completely flutters..

but the problem..is on off..

like it will do it lik 1 out 3 days..

sometimes 4 days..

its freakin annoying!

my recommendations

fit the std bov in plumb back mode

replace with a known working AFM

the likely suspect is your BOV, its probably venting vacuum pressure and its enough to annoy the AFM

which makes the car stutter and hesisate

well...i think ive faulted my problem..

i noticed wen on the freeway the other night..

i notice on my afc..that a/f% was on about 10%..then all of a sudden it would just randomly drop to lil 7/8%

nad i could feel the hesitation from this...it did it a couple of times..then it just went away.. ????? :D

but my throttle was in the same position...just cruisin..no boost or anything..

so what i can gather from this this its the afm cutting out..

i just open the silicone top black cover on the top off afm.

noticed the 3 wires that connect to the main board looked fine..

but i still did re-solder them...

and i gave the board a good clean of electrical contact cleaner...

hopfully shes all good now :P

Mine has the same problem, only happens when just opening the throttle off idle or 0%.

I'm running a microtech ecu with no afm.

the cause of mine is the throttle position sensor, i can watch it on the laptop and when the throttle is closed the throttle percentage creeps all over the place until i touch the throttle.

like 3lit3 32 says, "dead spot in the tps"

but at $208 i have not ordered a new one yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...