Jump to content
SAU Community

Recommended Posts

can i get payment details for

Bosch hid 8000k =] finally got moneys :D

PM sent

how much for a bosch kit h1 6000k + a spare pair of 4300k bulbs? do you sell bulbs individually??

Price is $225 for the kit and an extra $75 for extra bulbs.

So $300 all up.

Shoot me a PM if you would like to place an order.

  • Replies 115
  • Created
  • Last Reply

Top Posters In This Topic

I would only use 12,000k for show purposes only.

The light penetration is not great for normal night driving especially when its wet.

6000k is the highest i would go. Some people go 8000k for the bluer look.

Pull dust cap off.

Cut a 25-30mm diameter hole in the dust cap.

Remove halogen.

Replace with HID bulb.

Feed wire harness through hole in dust cap.

Fix the grommet to the hole.

Attach red bulb wire to ballast

Attach black bulb wire to headlight ground.

Attach ballast and HID bulb wires together. (there are -&+ on the side of the plug)

Fix the ballast to a safe place in the engine bay.

Rock and roll!

Hey i'm trying to work out what I need. I have a set of butchered 34 xenons wich dont work.

Just wondering the housing on the right hand side has d2r 35w, hir1 65w printed on top. The left housing has h1 55w,hir1 engraved over top of the print. Fairly sure one has had the compliance chop and one hasnt considering one missing ballast. can anyone recommend wich kit to order to get these lights to a near factory result.

sorry if i have missed something obvious, just a little confused :huh: !

recived my order today. Thanks for organising this now ive got sumthing to do on my lunch break 2morrow

No probs mate :/

Hey i'm trying to work out what I need. I have a set of butchered 34 xenons wich dont work.

Just wondering the housing on the right hand side has d2r 35w, hir1 65w printed on top. The left housing has h1 55w,hir1 engraved over top of the print. Fairly sure one has had the compliance chop and one hasnt considering one missing ballast. can anyone recommend wich kit to order to get these lights to a near factory result.

sorry if i have missed something obvious, just a little confused :huh: !

Choose either the D2R or H1, then modify one so its the same as the other.

I would choose H1 as it would be easier to convert the D2R to H1 rather than the H1 to D2R.

You would need bulb adaptors aswell.

Has anybody here purchased the 8000 one yet? If so, can u post up pics, still undecided whether i wanna go 6000 or 8000

IMO i wouldnt go higher than 6000k for everyday driving. Here is a pic of my 6000k

Photo0184.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...