Jump to content
SAU Community

Recommended Posts

i did the change. also went from a pfc to a wolf v500, with a much more in depth tune so i can't really coment on possible response loss, as i actually gained a lot of throttle response.

only ill effect i noticed was a small increase in the amount of times the car cranked over before it started. like maybe half a second.

There are many automakers who use MAP based systems with no problems at all, so why would you have problems with a map based standalone? If there were problems you can probably chalk it up to bad tuning or just a poorly designed standalone. I have zero problems with my standalone map based system even though I have a 5bar map sensor. Cold start, Drive-ability, Closed loop wide band Cruise, and deceleration are perfect.

Edited by maximajim

I went from ECR33 PFC L-jetro and converted it to run the GTR's D-jetro, Being that I mapped both setup's I can say this, the D-jetro was much easier to get nice dead stable AFR's, Drivability is better and fuel consumption is up by .5L better per 100km. (this was with no other mods done at all besides ECU change, I use FCedit, dual widebands, EGT and dual knocklinks when mapping RB's)

Best thing, no idle mess around! car just runs better all round. D-jetro's idle stabilization by timing is fantasic as well! almost as good as VEMS's

so far then .. it sounds all good.

I wasn't told map has any "problems" but that it isn't a good choice if you plan

to do mountain driving, as altitude (or big temp changes) muck with the tune vs maf.

My tuner says map will "feel different" in a possibly negative way, he didn't elaborate.

And people on sau have posted before that map is 'for race cars' and maf is for street,

and someone else on sau said map didn't work as well with multiple throttle bodies.

So I figured I'd ask if people had experienced a car before vs after with as much else

the same.

Edited by moneypit
I would say buy a ecu based on his recommendation or find another tuner who is competent in tuning a map system.

He should know that a good standalone will have temp and barometric trims (if needed).

He recommended going map, ecu is hks f-con,

but he just said it will feel different, and indicated I might not prefer it.

MAP sensor here too. Given the choice, i'll always go MAP over AFM. The number of AFM related issues that seem to pop up all the time is crazy. I went through 3 AFMs on my old car, and it still never was quite right.

MAP sensor here too. Given the choice, i'll always go MAP over AFM. The number of AFM related issues that seem to pop up all the time is crazy. I went through 3 AFMs on my old car, and it still never was quite right.

100% agree

MAP user here :D

so far then .. it sounds all good.

I wasn't told map has any "problems" but that it isn't a good choice if you plan

to do mountain driving, as altitude (or big temp changes) muck with the tune vs maf.

My tuner says map will "feel different" in a possibly negative way, he didn't elaborate.

And people on sau have posted before that map is 'for race cars' and maf is for street,

and someone else on sau said map didn't work as well with multiple throttle bodies.

So I figured I'd ask if people had experienced a car before vs after with as much else

the same.

The issue with multi throttle bodies and MAP, is the turbulunce.

You can get the same MAP reading, for a different throttle reading, and it plays havoc.

Good ECU's, like the Adaptronic, Motec, (I also believe Haltech, ViPEC and Autronic) run MAP vs TPS tuning.

I run MAP with the Adaptronic, and it has no issues at all.

Actually, it has quite a few benefits... I can run NO BOV, and not have a single issue.

I run an oil coated air filter, and not have it flood my AFM giving shit readings, resulting in poor idle...

Yeah mine doesnt take long to crank, and doesnt hunt on cold start. It does everything "normally" compared to an AFM based ECU.

....Well, except for having dramas when the AFM's get dirty and play up :D

Ford XR6 Turbo runs map and no issues there. So the whole map = race car is a little off.

The 1JZ and I believe 2JZ also run MAP...

Lots of manufacturers cars run MAP from the factory

My car takes a couple of cranks to fire, but that is purely the ECU, and NOTHING to do with it being MAP based.

I went through 3 AFMs on my old car

Brand new each time or 2nd hand? I'd be interested to hear the reasons why 3 brand new AFM's would have died in a short period.

If 2nd hand, then well... thats pretty much a pointless statement :D

Every AFM that i put in (new) works/worked fine without issue.

Ive played around with 2nd handies lately (due to time constraint) and had nothing but problems, but i accept that because im playing around with used parts and not brand new ones.

That said - go with what the tuner reccomends. He is tuning it afterall...

Straight MAP was poor on light throttle compared to AFMs but I had multiple throttle bodies (RB26). Redid the tune with MAP over TPS (combination of the 2) and found driveability every bit as equal as stock AFMs.

Best point => if I blow a cooler pipe/vacumm hose at the drags I can drive it home as is... unlike AFMs which would instantly foul the plugs. Best move I ever made was getting rid of the AFMs.

I went for a MAP because my tuner prefers it, he put it this way to me, although the AFM is a good bit of gear he has had more problems with that one piece of equipment than any other but finding out it is the AFM to be the problem is the real reason he prefers the MAP sensor, as for driveabilty I didnt really notice anything except the power increase.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...